Latest US Rumble Strips Contracts & Bids

This document contains specifications for various types of traffic barriers, including concrete, steel, and water-filled barriers, as well as longitudinal channelizing devices and temporary rumble strips. It also lists products removed from the compliant work zone traffic control devices (cwztcd) and fabrication details. The document includes contact information for various product manufacturers. There are requirements for vendor compliance with various laws and regulations, including insurance, taxes, and labor laws. The document also outlines the dispute resolution process and the terms and conditions of the contract. The document also includes information about the eligibility requirements for vendors, including the need to complete a Texas Family Code schedule and provide vendor data sheets.

The document contains standard terms and conditions for contracts, including definitions, requirements for bids, contract construction, liability provisions, performance and compliance, data and information control, and federal requirements. It details various aspects of the procurement process, including acceptance, agency, authorized dealers, bidders, default, deliverables, goods, invoices, lowest responsive and responsible bidder, MBE/EDGE certified, orders, prime vendor, procurement contract agreement, purchase, products, request for quote/invitation to bid/competitive sealed bidding, request for proposal, services, state, state data, specifications, time and materials contract, unbalanced bids, subvendors, quote/bid response requirements, samples, specifications, unit price and basis of award, quote/bid response firm, rejection of bids, deviations, disqualification of vendors, tie process, creation of the contract, regulatory contract requirements (antitrust, appropriation of funds, campaign contributions, compliance with law, conflict of interest, trade, debarment, drug-free workplace, equal employment opportunity, prohibition of offshore services, governing law, independent contractor acknowledgement, registration with the secretary of state, taxes, use of MBE and EDGE vendors, legal representation and rights, statute of limitations, contract amendments waiver, assignment/delegation, binding effect, language construction, injunctive relief, notices, order of priority, publicity, severability, subcontracting, survivorship, counterparts, order and payment provisions, defective invoices, payment due date and process, interest, reimbursable expenses, travel, liability provisions, general representations and warranties, indemnity, insurance, product recall, audits, FOB destination/prepaid allowed, returned goods, custom deliverables, force majeure excusable delay, contract performance management, quality assurance, contract remedies, suspension/termination, time is of the essence, strict performance, ohiobuys, data and information control, confidentiality, public records and retention of documents and information, security and safety rules, usage reports, data security and privacy terms, information technology service level agreement minimum requirements, federal requirements (nondiscrimination, compliance with regulations, solicitations for subcontractors, information and reports, sanctions for noncompliance, incorporation of provisions, pertinent nondiscrimination authorities). It also includes specific details on invoice requirements, payment processes, and insurance requirements.

Bidders must complete an online request for permission to bid. Electronic addendum updates will be posted on www. ***. *. * bond, signed by a Mississippi agent or qualified nonresident agent, with power of attorney attached, a cashier's check or certified check for five (5) percent of bid, payable to State of Mississippi, must accompany each proposal. Specimen proposals may be viewed and downloaded online at no cost at www. ***. *. * or purchased online at www. ***. *. * at a cost of ten dollars (****) per proposal plus a small convenience fee. Cash or checks will not be accepted as payment. The project completion is anticipated to be 97 working days. The notice of award is anticipated no later than September 9, 2025, and the date for notice to proceed (beginning of contract time) will be October 9, 2025. If the contractor requests a notice to proceed earlier than October 9, 2025, and it is agreeable with the department, the requested date will become the new notice to proceed date. Regardless of whether or not an early notice to proceed is granted, contract time will start at the original notice to proceed date. All requests for an early notice to proceed shall be sent to the project engineer who will forward it to the contract administration division. The contract documents do not include an official set of construction plans, but may, by reference, include some standard drawings when so specified in a notice to bidders entitled, standard drawings. The work to be accomplished using the pay items and corresponding specifications set forth in the contract is to overlay the following section of US 51 in Pike County from Osyka to Magnolia. The contractor shall erect and maintain construction signing, provide all signs, set up night time lane closures if needed, and traffic handling devices in accordance with the traffic control plan. All traffic control devices on this project should comply with the latest version of the MUTCD. Fluorescent orange sheeting shall be used on all construction and traffic control signs except for those designated in the standards to be black legend and border on white background. All MDOT owned right-of-way along US 51 shall be cleared completely of trees greater than 4 inches in diameter in maturity. Careful consideration should be given to any above ground utilities within the above-described limits, with clearing activities near those adhering to all applicable safety standards. Cut trees may either be hauled away, mulched in place, or another method approved by the engineer. Tree stumps shall be ground flush to the ground line unless directed otherwise by the engineer. Material may not be mulched in residential areas. Removal should be done so as not to disturb belowground root systems that may cause instability or slope failure, potentially damaging the roadway substructure. Any removal method alternatives to grinding mechanisms to remove remaining stumps to ground level should be preapproved by the district engineer with a plan to ensure substructure failure is unlikely to occur. If roadside foreslopes are steeper than 3:1 or include other roadway features that would make tree removal infeasible, risk assessment should be conducted by the project engineer and highway safety division. This work shall be paid for as ****: random clearing, per station. Each side of the roadway shall be measured separately. Prior to the overlay, the existing shoulders shall be clipped and surplus material shall be spread along the edge of the shoulders, fore slopes, or other adjacent areas as directed by the project engineer, and will be an absorbed item. The contractor shall fine mill at the following locations. The contractor shall place and variable of 9. 5mm, st, leveling asphalt at locations directed by the engineer. The contractor shall remove existing pavement markers prior to placing asphalt. The cost of removing these pavement markers is to be absorbed in other items bid. The contracto