Guard Mount Government Bids & RFPs

Lot 1: See Specifications Section 1. 00 ONLY ONLINE BIDS WILL BE ACCEPTED FOR THIS RFB. Emailed and hard copies delivered by any method WILL NOT BE ACCEPTED. See attached document How to Respond to an Online Bid through the Kentucky Vendor Self Service site ( updated). pdf. Please enter contact person, phone number and email in the Comments Section. Vendors should review and update, if necessary, all addresses and contact persons for their account prior to bid submission. This information will carry forward to a contract if awarded, therefore please ensure all information is correct.

Lot 2: Vendor supplied traffic control for drilled railroad rail drilling operation; Vendor shall provide flagging when requested. If Department provides traffic control, the flagging line item will not be included on the individual Delivery Order for Offset Drill with Operator. Item includes the appropriate number of flaggers for traffic control on the worksite. Each flagger will be paid at the hourly rate. With permission from the Engineer, the vendor may elect to use temporary traffic signals or portable traffic signals with appropriate signing in accordance with MUTCD or as directed by the Engineer. Vendor must also place and maintain appropriate work zone signing, flagger signs, flagger paddles, etc. in accordance with the MUTCD or as directed by the Engineer. Flagmen are required to wear appropriate safety equipment and must stay in constant communication with one another. Flaggers must work in accordance with Kentucky Dept of Highways Standard Drawings, in accordance with the MUTCD, and comply with Section 112 of the current Standard Specifications for Road and Bridge Construction at all times. Lane closures will only be permitted during daytime hours unless approved by the engineer. Payment will be made for the total number of man- hours worked for supplied traffic control each day. If vendor supplies portable traffic signals, payment by the man- hour will be based on number of man- hours flaggers would have been utilized instead of portable signals.

Lot 3: Vendor to provide used railroad rail. To be completed as stated in the extended description line 1 with the vendor providing the necessary used railroad rail. Use recycled ( used) railroad rails classified with a nominal weight of 130 lb/yd ( pounds per yard) size or greater. Use only visibly straight recycled rails with no splices. The Engineer will verify rail nominal weights ( manufacturer' s stamp with lb/yd, date, etc. ). Provide certification for nominal weight if the manufacturer' s stamp is unidentifiable.

Lot 4: Vendor to install cribbing at slide location as directed by the Engineer. Extend wall cribbing 2 feet to 16 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Use wall cribbing: recycled ( used) steel " w" beam guardrail shall be supplied by the KY Dept. of Transportation. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attach to the drilled railroad rails will be furnished by the vendor. The Vendor is responsible for picking up the ( used) steel " W" beam guardrail at the local county Maintenance garage. Any unused ( used) steel " W" beam guardrail shall be returned to the maintenance garage by the vendor.

Lot 5: Perform excavation as the slide repair dictates or as directed by the Engineer. Excavate each slide repair area to provide a platform for drilling the used railroad rails, if necessary. Excavate material as directed by the engineer wide enough to place cribbing and enough area for granular backfill. Equipment shall be capable of excavating a vertical trench to install cribbing up to 16 feet in depth from the roadway elevation. Method of excavation shall limit the damage or removal of the existing roadway pavement as much as possible. Excavating equipment bucket size and width shall be adjusted as directed by the engineer to achieve the excavation without damaging the pavement, utilities, drill steel, etc. Do not use excavated material from the site as fill material. If directed by the Engineer, additional excavation may be required to remove slide material from the roadway in order to maintain traffic or to eliminate the pavement break for future asphalt paving. Unless directed by the Engineer, excess excavation may be wasted at sites on the right- of- way, only if approved by the Engineer. Material may not be wasted in flood prone areas or in streams. If the Engineer deems no suitable sites are available within the right- of- way, the contractor will be required to waste excess material off the right- of- way at sites obtained by the contractor at no cost to the KY Dept. of Transportation. Excavation will be paid by field measurement.

Lot 6: Vendor to furnish backfill material. Place Geotextile fabric as directed by the engineer, the geotextile fabric shall be lapped as outlined by the manufacture recommendations and Kentucky Standard Specifications. The geotextile fabric shall wrap the granular backfill to provide separation from all earth embankment. Construct granular embankment behind railroad rails, cribbing and on slope, as per Section 206 of the Kentucky Standard Specifications for Road and Bridge Construction, Current Edition. Backfill material shall be placed and compacted to eliminate voids. Construct embankment up to the approximate existing pavement elevation. Use the following backfill materials: Kentucky aggregate gradation no. 2' s /23' s or larger to the bottom of pavement elevation and place DGA Base from the bottom of the pavement elevation to the top of the existing pavement separated with Geotextile fabric as directed by the engineer. Backfill material shall meet requirements of Section 805 of the Kentucky Standard Specifications for Road and Bridge Construction, Current Edition. Backfill material delivered to the project, will only be accepted with a certified weigh ticket. A conversion factor of 1. 3 tons per cubic yard will be used to pay for all gradations of aggregate Backfill material delivered to the project. The Engineer will use visual inspection and/or material testing, as applicable to determine acceptability. Geotextile fabric shall be provided by the vendor. Vendor to furnish backfill material and labor to install geotextile fabric.

Lot 7: Vendor furnished laborer to trim tree limbs, extend Department furnished culvert pipe through crib wall, and taking down guardrail and stacking for the Department to pick up. The Department will be responsible for picking guardrail up and delivering to maintenance facility.

Lot 8: Vendor furnished bucket truck with operator capable of clearing tree limbs for a 40 feet drill mast. Vendor operator must be properly trained for the bucket truck operations and wear the appropriate safety equipment.

Lot 9: Vendor is to furnish and Install TY IV filter fabric for separation of the Backfill Material and Roadway Material. Payment per SQYD will include all labor, materials, and incidentals necessary to correctly install filter fabric in the slide area.

Lot 10: Vendor to furnish and install cribbing at slide location as directed by the Engineer. Vendor furnished cribbing must be galvanized guardrail, reinforced concrete panels, or equivalent material as approved by the engineer. The cribbing material must be corrosion resistant and be capable of holding backfill material across a span of 3 to 4 feet. Extend wall cribbing 2 feet to 16 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attaching to the drilled railroad rails will be furnished by the vendor.

Lot 11: Vendor furnished cribbing material must be galvanized guardrail. The guardrail shall be delivered and paid in 12. 5 LF sections. 25 LF guardrail sections will be considered /accepted upon the engineer' s approval. The guardrail material must be corrosion resistant, hole punched as shown for standard guardrail installation, and straight. KYTC will unload the material. Minimum order of 5, 625 Sq. Ft. MODIFIED ROTARY DRILL WITH OPERATOR( S). DRILL TO BE TRUCK MOUNTED AND CAPABILITY OF DRILLING 7" TO 10" DIAMETER HOLES 40 FEET INTO SOIL AND ROCK. ROTARY DRILL MUST HAVE CAPACITY OF DRILLING OFFSET A MINIMUM OF FIVE ( 5) FEET FROM THE EDGE OF THE TIRE TO THE CENTER OF THE HOLES, DRILLING FROM EITHER SIDE OF THE CARRIER AND ON A 15% SLOPE. MAST JIB SHALL BE ABLE TO LIFT AND DROP INTO THE HOLES, STEEL RAILROAD RAILS UP TO 40 FEET IN LENGTH AND WEIGHING UP TO 2, 000 POUNDS. DRILL SHALL HAVE A MINIMUM 150 H. P. MOTOR AND AT LEAST A 300 CFM COMPRESSOR CAPABLE OF 16, 000 POUNDS OF PULL DOWN PRESSURE. PAYMENT WILL BE MADE ON THE PART OF THE RAIL THAT IS SATISFACTORILY PLACE BELOW GROUND LEVEL. NO PAYMENT WILL BE MADE FOR THE PART OF THE RAIL EXTENDING ABOVE THE HOLE. CONTRACTOR IS RESPONSIBLE FOR CUTTING ANY RAILROAD STEEL THAT IS NOT FLUSH WITH THE ESTIMATED FINISHED SHOULDER AFTER BEING DROPPED INTO DRILLED HOLES. CONTRACTOR MUST BE ABLE TO DRILL AND INSTALL 800 FT OF RAILROAD STEEL PER 8 HOUR WORKDAY. LEEWAY WILL BE GIVEN FOR WEATHER AND UNFORSEEN CIRCUMSTANCES AT THE DEPARTMENTS DISCRETION. THE TRANSPORTATION CABINET SHALL PROVIDE RAILROAD RAILS, MAKE NECESSARY SITE PREPARATION AND FURNISH NECESSARY TRAFFIC CONTROL.

Lot 12: Modified rotary drill with operator( s). Drill to be truck mounted and capability of drilling 7" to 10" diameter holes 40 feet into soil and rock. Rotary drill must have capacity of drilling offset a minimum of five ( 5) feet from the edge of the tire to the center of the holes, drilling from either side of the carrier and on a 15% slope. Mast jib shall be able to lift and drop into the holes, steel railroad rails up to 40 feet in length and weighing up to 2, 000 pounds. Drill shall have a minimum 150 h. P. Motor and at least a 300 cfm compressor capable of 16, 000 pounds of pull down pressure. Payment will be made on the part of the rail that is satisfactorily place below ground level. No payment will be made for the part of the rail extending above the hole. Contractor is responsible for cutting any railroad steel that is not flush with the estimated finished shoulder after being dropped into drilled holes. Contractor must be able to drill and install 800 ft of railroad steel per 8 hour workday. Leeway will be given for weather and unforseen circumstances at the departments discretion. The transportation cabinet shall provide railroad rails, make necessary site preparation and furnish necessary traffic control.

Lot 13: Vendor to provide used railroad rail. This includes drilling the hole, providing and placing the rail. Use only visibly straight recycled rails with no splices. The Engineer will verify rail nominal weights ( manufacturer' s stamp with lb/yd, date, etc. ). Provide certification for nominal weight if the manufacturer' s stamp is unidentifiable. This line item shall be used for all work paid using FEDERAL funds. MODIFIED ROTARY DRILL WITH OPERATOR( S). DRILL TO BE TRUCK MOUNTED AND CAPABILITY OF DRILLING 7" TO 10" DIAMETER HOLES 40 FEET INTO SOIL AND ROCK. ROTARY DRILL MUST HAVE CAPACITY OF DRILLING OFFSET A MINIMUM OF FIVE ( 5) FEET FROM THE EDGE OF THE TIRE TO THE CENTER OF THE HOLES, DRILLING FROM EITHER SIDE OF THE CARRIER AND ON A 15% SLOPE. MAST JIB SHALL BE ABLE TO LIFT AND DROP INTO THE HOLES, STEEL RAILROAD RAILS UP TO 40 FEET IN LENGTH AND WEIGHING UP TO 2, 000 POUNDS. DRILL SHALL HAVE A MINIMUM 150 H. P. MOTOR AND AT LEAST A 300 CFM COMPRESSOR CAPABLE OF 16, 000 POUNDS OF PULL DOWN PRESSURE. PAYMENT WILL BE MADE ON THE PART OF THE RAIL THAT IS SATISFACTORILY PLACE BELOW GROUND LEVEL. NO PAYMENT WILL BE MADE FOR THE PART OF THE RAIL EXTENDING ABOVE THE HOLE. CONTRACTOR IS RESPONSIBLE FOR CUTTING ANY RAILROAD STEEL THAT IS NOT FLUSH WITH THE ESTIMATED FINISHED SHOULDER AFTER BEING DROPPED INTO DRILLED HOLES. CONTRACTOR MUST BE ABLE TO DRILL AND INSTALL 800 FT OF RAILROAD STEEL PER 8 HOUR WORKDAY. LEEWAY WILL BE GIVEN FOR WEATHER AND UNFORSEEN CIRCUMSTANCES AT THE DEPARTMENTS DISCRETION. THE TRANSPORTATION CABINET MAKE NECESSARY SITE PREPARATION AND FURNISH NECESSARY TRAFFIC CONTROL.

Lot 1: See Specification Section 1. 00 ONLY ONLINE BIDS WILL BE ACCEPTED FOR THIS RFB. Emailed and hard copies delivered by any method WILL NOT BE ACCEPTED. See attached document How to Respond to an Online Bid through the Kentucky Vendor Self Service site ( updated). pdf. Please enter contact person, phone number and email in the Comments Section. Vendors should review and update, if necessary, all addresses and contact persons for their account prior to bid submission. This information will carry forward to a contract if awarded, therefore please ensure all information is correc

Lot 2: Vendor supplied traffic control for drilled railroad rail drilling operation; Vendor shall provide flagging when requested. If Department provides traffic control, the flagging line item will not be included on the individual Delivery Order for Offset Drill with Operator. Item includes the appropriate number of flaggers for traffic control on the worksite. Each flagger will be paid at the hourly rate. With permission from the Engineer, the vendor may elect to use temporary traffic signals or portable traffic signals with appropriate signing in accordance with MUTCD or as directed by the Engineer. Vendor must also place and maintain appropriate work zone signing, flagger signs, flagger paddles, etc. in accordance with the MUTCD or as directed by the Engineer. Flagmen are required to wear appropriate safety equipment and must stay in constant communication with one another. Flaggers must work in accordance with Kentucky Dept of Highways Standard Drawings, in accordance with the MUTCD, and comply with Section 112 of the current Standard Specifications for Road and Bridge Construction at all times. Lane closures will only be permitted during daytime hours unless approved by the engineer. Payment will be made for the total number of man- hours worked for supplied traffic control each day. If vendor supplies portable traffic signals, payment by the man- hour will be based on number of man- hours flaggers would have been utilized instead of portable signals.

Lot 3: Vendor to provide used railroad rail. To be completed as stated in the extended description line 1 with the vendor providing the necessary used railroad rail. Use recycled ( used) railroad rails classified with a nominal weight of 130 lb/yd ( pounds per yard) size or greater. Use only visibly straight recycled rails with no splices. The Engineer will verify rail nominal weights ( manufacturer' s stamp with lb/yd, date, etc. ). Provide certification for nominal weight if the manufacturer' s stamp is unidentifiable.

Lot 4: Vendor to install cribbing at slide location as directed by the Engineer. Extend wall cribbing 2 feet to 16 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Use wall cribbing: recycled ( used) steel " w" beam guardrail shall be supplied by the KY Dept. of Transportation. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attach to the drilled railroad rails will be furnished by the vendor. The Vendor is responsible for picking up the ( used) steel " W" beam guardrail at the local county Maintenance garage. Any unused ( used) steel " W" beam guardrail shall be returned to the maintenance garage by the vendor.

Lot 5: Perform excavation as the slide repair dictates or as directed by the Engineer. Excavate each slide repair area to provide a platform for drilling the used railroad rails, if necessary. Excavate material as directed by the engineer wide enough to place cribbing and enough area for granular backfill. Equipment shall be capable of excavating a vertical trench to install cribbing up to 16 feet in depth from the roadway elevation. Method of excavation shall limit the damage or removal of the existing roadway pavement as much as possible. Excavating equipment bucket size and width shall be adjusted as directed by the engineer to achieve the excavation without damaging the pavement, utilities, drill steel, etc. Do not use excavated material from the site as fill material. If directed by the Engineer, additional excavation may be required to remove slide material from the roadway in order to maintain traffic or to eliminate the pavement break for future asphalt paving. Unless directed by the Engineer, excess excavation may be wasted at sites on the right- of- way, only if approved by the Engineer. Material may not be wasted in flood prone areas or in streams. If the Engineer deems no suitable sites are available within the right- of- way, the contractor will be required to waste excess material off the right- of- way at sites obtained by the contractor at no cost to the KY Dept. of Transportation. Excavation will be paid by field measurement.

Lot 6: Vendor to furnish backfill material. Place Geotextile fabric as directed by the engineer, the geotextile fabric shall be lapped as outlined by the manufacture recommendations and Kentucky Standard Specifications. The geotextile fabric shall wrap the granular backfill to provide separation from all earth embankment. Construct granular embankment behind railroad rails, cribbing and on slope, as per Section 206 of the Kentucky Standard Specifications for Road and Bridge Construction, Current Edition. Backfill material shall be placed and compacted to eliminate voids. Construct embankment up to the approximate existing pavement elevation. Use the following backfill materials: Kentucky aggregate gradation no. 2' s /23' s or larger to the bottom of pavement elevation and place DGA Base from the bottom of the pavement elevation to the top of the existing pavement separated with Geotextile fabric as directed by the engineer. Backfill material shall meet requirements of Section 805 of the Kentucky Standard Specifications for Road and Bridge Construction, Current Edition. Backfill material delivered to the project, will only be accepted with a certified weigh ticket. A conversion factor of 1. 3 tons per cubic yard will be used to pay for all gradations of aggregate Backfill material delivered to the project. The Engineer will use visual inspection and/or material testing, as applicable to determine acceptability. Geotextile fabric shall be provided by the vendor. Vendor to furnish backfill material and labor to install geotextile fabric.

Lot 7: Vendor furnished laborer to trim tree limbs, extend Department furnished culvert pipe through crib wall, and taking down guardrail and stacking for the Department to pick up. The Department will be responsible for picking guardrail up and delivering to maintenance facility.

Lot 8: Vendor furnished bucket truck with operator capable of clearing tree limbs for a 40 feet drill mast. Vendor operator must be properly trained for the bucket truck operations and wear the appropriate safety equipment.

Lot 9: Vendor is to furnish and Install TY IV filter fabric for separation of the Backfill Material and Roadway Material. Payment per SQYD will include all labor, materials, and incidentals necessary to correctly install filter fabric in the slide area.

Lot 10: Vendor to furnish and install cribbing at slide location as directed by the Engineer. Vendor furnished cribbing must be galvanized guardrail, reinforced concrete panels, or equivalent material as approved by the engineer. The cribbing material must be corrosion resistant and be capable of holding backfill material across a span of 3 to 4 feet. Extend wall cribbing 2 feet to 16 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attaching to the drilled railroad rails will be furnished by the vendor.

Lot 11: Vendor furnished cribbing material must be galvanized guardrail. The guardrail shall be delivered and paid in 12. 5 LF sections. 25 LF guardrail sections will be considered /accepted upon the engineer' s approval. The guardrail material must be corrosion resistant, hole punched as shown for standard guardrail installation, and straight. KYTC will unload the material. Minimum order of 5, 625 Sq. Ft. MODIFIED ROTARY DRILL WITH OPERATOR( S). DRILL TO BE TRUCK MOUNTED AND CAPABILITY OF DRILLING 7" TO 10" DIAMETER HOLES 40 FEET INTO SOIL AND ROCK. ROTARY DRILL MUST HAVE CAPACITY OF DRILLING OFFSET A MINIMUM OF FIVE ( 5) FEET FROM THE EDGE OF THE TIRE TO THE CENTER OF THE HOLES, DRILLING FROM EITHER SIDE OF THE CARRIER AND ON A 15% SLOPE. MAST JIB SHALL BE ABLE TO LIFT AND DROP INTO THE HOLES, STEEL RAILROAD RAILS UP TO 40 FEET IN LENGTH AND WEIGHING UP TO 2, 000 POUNDS. DRILL SHALL HAVE A MINIMUM 150 H. P. MOTOR AND AT LEAST A 300 CFM COMPRESSOR CAPABLE OF 16, 000 POUNDS OF PULL DOWN PRESSURE. PAYMENT WILL BE MADE ON THE PART OF THE RAIL THAT IS SATISFACTORILY PLACE BELOW GROUND LEVEL. NO PAYMENT WILL BE MADE FOR THE PART OF THE RAIL EXTENDING ABOVE THE HOLE. CONTRACTOR IS RESPONSIBLE FOR CUTTING ANY RAILROAD STEEL THAT IS NOT FLUSH WITH THE ESTIMATED FINISHED SHOULDER AFTER BEING DROPPED INTO DRILLED HOLES. CONTRACTOR MUST BE ABLE TO DRILL AND INSTALL 800 FT OF RAILROAD STEEL PER 8 HOUR WORKDAY. LEEWAY WILL BE GIVEN FOR WEATHER AND UNFORSEEN CIRCUMSTANCES AT THE DEPARTMENTS DISCRETION. THE TRANSPORTATION CABINET SHALL PROVIDE RAILROAD RAILS, MAKE NECESSARY SITE PREPARATION AND FURNISH NECESSARY TRAFFIC CONTROL.

Lot 12: Modified rotary drill with operator( s). Drill to be truck- mounted and capability of drilling 7" to 10" diameter holes 40 feet into soil and rock. Rotary drill must have capacity of drilling offset a minimum of five ( 5) feet from the edge of the tire to the center of the holes, drilling from either side of the carrier and on a 15% slope. Mast jib shall be able to lift and drop into the holes steel railroad rails up to 40 feet in length and weighing up to 2, 000 pounds. Drill shall have a minimum 150 h. P. Motor and at least a 300 cfm compressor capable of 16, 000 pounds of pull down pressure. Payment will be made on the part of the rail that is satisfactorily placed below ground level. No payment will be made for the part of the rail extending above the hole. Contractor is responsible for cutting any railroad steel that is not flush with the estimated finished shoulder after being dropped into drilled holes. Contractor must be able to drill and install 800 ft of railroad steel per 8- hour workday. Leeway will be given for weather and unforeseen circumstances at the department' s discretion. The transportation cabinet shall provide railroad rails, make necessary site preparation and furnish necessary traffic control.

Lot 13: Vendor to provide used railroad rail. This includes drilling the hole, providing and placing the rail. Use only visibly straight recycled rails with no splices. The Engineer will verify rail nominal weights ( manufacturer' s stamp with lb/yd, date, etc. ). Provide certification for nominal weight if the manufacturer' s stamp is unidentifiable. This line item shall be used for all work paid using STATE funds. MODIFIED ROTARY DRILL WITH OPERATOR( S). DRILL TO BE TRUCK MOUNTED AND CAPABILITY OF DRILLING 7" TO 10" DIAMETER HOLES 40 FEET INTO SOIL AND ROCK. ROTARY DRILL MUST HAVE CAPACITY OF DRILLING OFFSET A MINIMUM OF FIVE ( 5) FEET FROM THE EDGE OF THE TIRE TO THE CENTER OF THE HOLES, DRILLING FROM EITHER SIDE OF THE CARRIER AND ON A 15% SLOPE. MAST JIB SHALL BE ABLE TO LIFT AND DROP INTO THE HOLES, STEEL RAILROAD RAILS UP TO 40 FEET IN LENGTH AND WEIGHING UP TO 2, 000 POUNDS. DRILL SHALL HAVE A MINIMUM 150 H. P. MOTOR AND AT LEAST A 300 CFM COMPRESSOR CAPABLE OF 16, 000 POUNDS OF PULL DOWN PRESSURE. PAYMENT WILL BE MADE ON THE PART OF THE RAIL THAT IS SATISFACTORILY PLACE BELOW GROUND LEVEL. NO PAYMENT WILL BE MADE FOR THE PART OF THE RAIL EXTENDING ABOVE THE HOLE. CONTRACTOR IS RESPONSIBLE FOR CUTTING ANY RAILROAD STEEL THAT IS NOT FLUSH WITH THE ESTIMATED FINISHED SHOULDER AFTER BEING DROPPED INTO DRILLED HOLES. CONTRACTOR MUST BE ABLE TO DRILL AND INSTALL 800 FT OF RAILROAD STEEL PER 8 HOUR WORKDAY. LEEWAY WILL BE GIVEN FOR WEATHER AND UNFORSEEN CIRCUMSTANCES AT THE DEPARTMENTS DISCRETION. THE TRANSPORTATION CABINET MAKE NECESSARY SITE PREPARATION AND FURNISH NECESSARY TRAFFIC CONTROL.

Lot 1: Shirts - elbeco reflex long sleeve shirts ( standard sizes xs- xl) color: navy blue style: mens # ****, womens # **** no substitutions or equivalents. Shirts should be sized to accommodate soft body armor. Patches as follows a. Left arm shoulder: agency patch ( see attached), sewn directly on left sleeve ( no velcro). B. Left chest: 3" academy patch ( see attached), velcro ( velcro should be cut to fit patch size) just above left pocket and centered. C. Right chest: just above pocket and centered, direct embroidered with trainees first initial ( period) and last name. 1/2 inch gold thread ( must match thread on academy patch). All block style capital letters ( i. E. " j. Doe"). Exceptionally long names may be adjusted to a smaller font size if necessary. However, all fonts shall be as close to the specified size as possible.

Lot 2: Additional upcharge for oversizing ( 2xl) for item # 1 indicate the amount to be added to bid price for item # 1 for oversizing

Lot 3: Additional upcharge for oversizing ( 3xl) for item # 1 indicate the amount to be added to bid price for item # 1 for oversizing

Lot 4: Set of shirt stays ( 4 set) polyester, straight style color: black

Lot 5: Pants - 5. 11 tac lite pdu ( standard sizes) color: code 750 midnight navy style: mens # ****, womens # **** no substitutions or equivalents. Sewn- in creases and/or pleats. Name tape, black in color with black merrowed edge, 5. 5" w x 1" h. Trainees name embroidered in all block- style capital letters, 1/2" white thread, first initial ( period), last name ( i. E. J. Doe). Name tape bottom to touch top of right rear pants pocket and centered

Lot 6: Additional upcharge for oversizing ( waist over 44") for item # 5 indicate the amount to be added to bid price for item # 5 for oversizing

Lot 7: Tie, clip- on, color plain navy blue, wool/polyester blend fabric

Lot 8: Tie- bar, plain ( no state seal or logo of any kind), color silver, size 2" x 5/16"

Lot 9: Plain leather garrison belt ( minimum 1 3/4 inches wide) color: black with square ( no rounded corners) silver 2" x 2" buckle belt end not to exceed 4" past buckle

Lot 10: Additional upcharge for oversizing ( waist over 44") for item # 9 indicate the amount to be added to bid price for item # 9 for oversizing

Lot 11: Tactical style boot, 5. 11 model # **** a/t 8" color: black side zipper, waterproof

Lot 12: # m- 65 - black field jacket, u. S. Government issue type the jacket will have the american flag on the right- side arm shoulder, with blue field forward agency patch on the left- side arm shoulder the trainees name above the right- side breast pocket, using a black 1 inch name tape, embroidered with the trainees first initial ( period), last name, in 1/2 inch gold thread to match thread on academy patch

Lot 13: Raincoat, 3/4 length, police type color: black/green reversible ansi class ii, with removable hood, zipper and snap closures, no external markings or lettering

Lot 14: Safariland sam browne duty belt, model #: 87- 28bw 2. 25" wide color: black basket weave all leather, and all snaps and metal on belt must be brass in color. Belt buckle rectangular in color brass.

Lot 15: Additional upcharge for oversizing ( waist over 44") for item # 14 indicate the amount to be added to bid price for item # 14 for oversizing

Lot 16: Safariland 65 belt- keeper ( 4pk) model #: 65- 4- 4b, black basketweave with brass snap 2. 25"

Lot 17: Handcuffs with two ( 2) key sets. Peerless or smith & wesson brand, chain link type metal in design with double locking capacity. Composite handcuffs are not authorized

Lot 18: Safariland handcuff case, model #: 190- 4b color: black basket weave, brass color snap closure

Lot 19: Safariland double magazine pouch, model 77 color: black basket weave

Lot 20: Safariland # **** holster color: black als/sls mid- ride, level iii retention duty holster, to fit glock . 45 with streamlight tlr1- hl light

Lot 21: Safariland holster quick locking system kit, color black, type: kit 1

Lot 22: Monadnock expandable straight baton, length 22" firm rubber grip color: flat black

Lot 23: Mondadnock expandable baton holder model #: **** color: flat black

Lot 24: Complete handgun cleaning kit, hoppes 9mm with storage box model #: pc038

Lot 25: Tactical gun mounted light ( streamlight tlr1- hl) model #: **** color: black

Lot 26: Tactical gloves 5. 11 taclite 4. 0 gloves color: black

Lot 27: Cat- combat tourniquet # nar- 30- ****, north american rescue * must be compatible with item # 28

Lot 28: Cat tourniquet holder model #: nar- 80- **** color: black * must be compatible with item # 27

Lot 29: Streamlight flashlight, protac **** * must be compatible with item 30

Lot 30: Streamlight stinger 2020 flashlight holder with closed top color: black nylon with brass colored snap * must be compatible with item # 29

Lot 31: Duty bag/backpack (" assault cargo" type), rothco tactical canvas material with nylon straps size: large or approximately 24" x15" x13" color: all black name strip of recruits name embroidered in all block style capital letters, 1/2" white thread, first initial ( period), last name ( i. E. J. Doe) sewn even with and between the looped carrying handles.

Lot 32: Wrap around eye protection, clear lenses with either clear or black arms

Lot 33: Hearing protection, ear- muff type model #: **** walkers razor slim electronic earmuffs color: black

Lot 34: Gym shorts: sport- tek, model # st355 ( standard sizes xs- xl) color: navy blue length must be between the mid- thigh and the top of the knee recruits last name across the buttocks area in 2" high silver reflective block letters

Lot 35: Additional upcharge for oversizing ( 2xl) for item # 32 indicate the amount to be added to bid price for item # 32 for oversizing

Lot 36: Additional upcharge for oversizing ( 3xl) for item # 32 indicate the amount to be added to bid price for item # 32 for oversizing

Lot 37: Gym shirts: sport- tek, model # st350 ( standard sizes xs- xl) color: navy blue crew- neck t- shirts, recruits last name across both the front chest and mid- back in 2- inch- high silver reflective block letters

Lot 38: Additional upcharge for oversizing ( 2xl) for item # 35 indicate the amount to be added to bid price for item # 35 for oversizing

Lot 39: Additional upcharge for oversizing ( 3xl) for item # 35 indicate the amount to be added to bid price for item # 35 for oversizing

Lot 40: Dark navy cotton drawstring sweatpants ( standard sizes xs- xl) elastic leg opening ( no straight legged or hemmed) no pockets recruits last name across the buttocks area in 2- inch - high silver reflective letters

Lot 41: Additional upcharge for oversizing ( 2xl) for item # 38 indicate the amount to be added to bid price for item # 38 for oversizing

Lot 42: Additional upcharge for oversizing ( 3xl) for item # 38 indicate the amount to be added to bid price for item # 38 for oversizing

Lot 43: Cotton hooded sweatshirts ( standard sizes xs- xl) color: dark navy recruits last name across the front chest and mid- back in 2- inch - high, silver reflective block letters, and front pocket

Lot 44: Additional upcharge for oversizing ( 2xl) for item # 41 indicate the amount to be added to bid price for item # 41 for oversizing

Lot 45: Additional upcharge for oversizing ( 3xl) for item # 41 indicate the amount to be added to bid price for item # 41 for oversizing

Lot 46: Cotton crew neck sweatshirts ( standard sizes xs- xl) color: dark navy recruits last name across both the front chest and mid- back in 2- inch - high, silver reflective block letters

Lot 47: Additional upcharge for oversizing ( 2xl) for item # 44 indicate the amount to be added to bid price for item # 44 for oversizing

Lot 48: Additional upcharge for oversizing ( 3xl) for item # 44 indicate the amount to be added to bid price for item # 44 for oversizing

Lot 49: Compression shorts, spandex nylon/poly blend materials ( standard sizes xs- xl) color: dark navy, black, or white only male: 6"- 10" inseam, female: 3"- 8" inseam

Lot 50: Additional upcharge for oversizing ( 2xl) for item # 47 indicate the amount to be added to bid price for item # 47 for oversizing

Lot 51: Additional upcharge for oversizing ( 3xl) for item # 47 indicate the amount to be added to bid price for item # 47 for oversizing

Lot 52: Plain military style cotton " shoe socks color: black no markings and/or stripes

Lot 53: White, cotton, ankle- length athletic socks, no marks or stripes

Lot 54: Baseball style cap, brand yupong, style # **** color: black no neoprene or mesh, no substitutions or equivalents 2. 5" academy patch sewn on front, last name directly embroidered on the rear of the cap in 3/8" gold block letters ( must match thread on academy patch)

Lot 55: Knit watch cap color: black recruits last name direct embroidered on the rear of the cap in 1/2- inch gold block letters ( must match thread of academy patch)

Lot 56: Reflective traffic vest, department issued high- visibility yellow all one color or with black stitching/piping, and no writing on vest

Lot 57: Hayabusa protective headgear, model #: ****- **** mma style, t3 adjustable, color black

Lot 58: Fingerless training gloves, model # ****- **** 6 oz, mma style, color black

Lot 59: Molded mouth guard with case

Lot 60: Safariland /bianchi nylon duty belt, model #: **** 2. 25" wide, color: black

Lot 61: Safariland /bianchi nylon duty liner belt, model # **** 1. 5" wide, color: black

Lot 62: Safariland /bianchi nylon duty belt keepers, model #: **** snap closure, fits 2. 25 belt width color: black

Lot 63: Safariland /bianchi nylon double magazine pouch with hidden snap closure, model #: **** snap closure, fits 2. 25 belt width color: black

Lot 64: Oversized pocket handcuff key, model # zt101 4. 75" long

Lot 65: Shirts - elbeco reflex long sleeve shirts ( standard sizes xs- xl) color: navy blue style: mens # **** , womens # **** no substitutions or equivalents. Should be sized to accommodate soft body armor underneath patches as follows a. Left arm shoulder: agency patch ( see attached), sewn directly on left sleeve ( no velcro) b. Left chest: 3" monmouth county police academy ( mcpa) patch ( see attached), velcro ( velcro should be cut to fit patch size) c. Right chest: centered to mcpa patch on left chest, direct embroidered with trainees first initial( period), last name in 1/2 inch gold thread ( to match thread on mcpa patch), all block style capital letters. ( i. E. J. Doe. ) exceptionally long names may be adjusted to a smaller font size if necessary. However, all fonts shall be as close to the specified size as possible.

Lot 66: Set of shirt stays ( 4 set, 2 per side) polyester, straight style color: black

Lot 67: Pants - 5. 11 tac lite pdu ( standard sizes) color: code 750 midnight navy style: mens # ****, womens # **** no substitutions or equivalents. Sewn- in creases and/or pleats. Name tape, black in color with black merrowed edge, 5. 5" w x 1" h. Trainees name embroidered in all block- style capital letters, 1/2" white thread, first initial ( period), last name ( i. E. J. Doe). Name tape bottom to touch top of right rear pants pocket and centered

Lot 68: Tie, clip- on, color plain navy blue, wool/polyester blend fabric

Lot 69: Tie- bar, plain ( no state seal or logo of any kind), color silver, size 2" x 5/16"

Lot 70: Plain leather garrison belt ( minimum 1 3/4 inches wide) color: black with square ( no rounded corners) silver 2" x 2" buckle belt end not to exceed 4" past buckle

Lot 71: # m- 65 - black field jacket, u. S. Government issue type the jacket will have the american flag on the right- side arm shoulder, with blue field forward agency patch on the left- side arm shoulder the trainees name above the right- side breast pocket, using a black 1 inch name tape, embroidered with the trainees first initial ( period), last name, in 1/2 inch gold thread to match thread on mcpa patch

Lot 72: Raincoat, 3/4 length, police type color: black/green reversible ansi class ii, with removable hood, zipper and snap closures, no external markings or lettering

Lot 73: Complete handgun cleaning gear consisting of: - cleaning rod( s) with attachments - bore brush( s) - cleaning patches - cotton swabs - plastic toothbrushes - clean absorbent cloths - bore cleaner or powder solvent, and lubricant, an agency authorized firearm cleaner lubricant protectant ( clp) may be used in place of bore cleaner and lubricant

Lot 74: Armor flex tactical gloves color: black style: # pfu- 18

Lot 75: North american rescue torniquet color: black as per agency standards

Lot 76: North american rescue torniquet holder color: black plastic ( with pouch or holder), affixed to duty belt or holster mount as per agency standards to be compatible with item # 67 above

Lot 77: Duty bag/backpack (" assault cargo" type), rothco tactical canvas material with nylon straps size: large or approximately 24" x15" x13" color: all black name strip of recruits name embroidered in all block style capital letters, 1/2" white thread, first initial ( period), last name ( i. E. J. Doe) sewn even with and between the looped carrying handles.

Lot 78: Gym shorts: sport- tek, model # st355 ( standard sizes xs- xl) color: navy blue length must be between the mid- thigh and the top of the knee recruits last name across the buttocks area in 2" high silver reflective block letters

Lot 79: Gym shirts: sport- tek, model # st350 ( standard sizes xs- xl) color: navy blue crew- neck t- shirts, recruits last name across both the front chest and mid- back in 2- inch- high silver reflective block letters

Lot 80: Dark navy cotton drawstring sweatpants ( standard sizes xs- xl) elastic leg opening ( no straight legged or hemmed) no pockets recruits last name across the buttocks area in 2- inch - high silver reflective letters

Lot 81: Cotton hooded sweatshirts ( standard sizes xs- xl) color: dark navy recruits last name across the front chest and mid- back in 2- inch - high, silver reflective block letters, and front pocket

Lot 82: Cotton crew neck sweatshirts ( standard sizes xs- xl) color: dark navy recruits last name across both the front chest and mid- back in 2- inch - high, silver reflective block letters

Lot 83: White, cotton, ankle- length athletic socks, no marks or stripes

Lot 84: Baseball style cap, brand yupong, style # **** color: black no neoprene or mesh, no substitutions or equivalents 2. 5" mcpa patch sewn on front, last name directly embroidered on the rear of the cap in 3/8" gold block letters ( must match thread on academy patch)

Lot 85: Knit watch cap color: black recruits last name direct embroidered on the rear of the cap in 1/2- inch gold block letters ( must match thread of mcpa academy patch)

Lot 86: Plain military style cotton " shoe socks color: black no markings and/or stripes

Lot 87: Rocky black round toe stitched, all leather, military type combat jump boot lace up front, side zipper optional, clean highly polishable boots - no sneaker type style: mens # ****, womens # ****

Lot 88: Laderal pocket mask with gloves and wipe in yellow hardcase