Stump Cutter Government Bids & RFPs
Government bid alerts, regional filters, and fast access to documents
See also
Last updated on 10/19/2026.
Dept Of Defense- Dept Of The Army- Amc- Acc- Mission & Installation Contracting Command- 419Th Csb- W6Qm Micc- Ft Drum
Brush Cutter/ Sapling Cutter/ Stump Jumper
12 foot bat wing right side wing only - Fully welded top deck. Gearbox seal protection. 6- inch blade overlap. Welded top deck. Cut brush and saplings up to 3- inch. Must have a stump jumper, backed with a 1- inch thick mounting bar. Self- leveling pull- type hitch. Rear facing LED signal light
Batwing mower 12 foot bat wing right side wing only - fully welded top deck. gearbox seal protection. 6- inch blade overlap. welded top deck. cut brush and saplings up to 3- inch. must have a stump jumper, backed with a 1- inch thick mounting bar. self- leveling pull- type hitch. rear facing led signal light - **** miscellaneous service and trade equipment miscellaneous service and trade equipment fully welded top deck. gearbox seal protection. 6 inch blade overlap. welded top deck. cut brush and saplings up to 3 inch. must have a stump jumper, backed with a 1 inch thick mounting bar. self leveling pull type hitch. rear facing led signal lights. 1 right side hinged wing section. 1 inch solid hinge rods. wing transport lock. 1 inch enclosed front to rear dual leveling rods. 5 inch square rear axle tubing. 540 rpm: center: 17, 377 fpm 88. 3 mps, wings: 17, 329 fpm 88 **** rpm: center: 18, 165 fpm 92. 3 mps, wings: 18, 317 fpm 93. 1 mps. spring cushioned on center axle. bar tite hitch. 1 2 inch x 3 inch wel
Bid Close Date:
Interior, Department Of The- U. S. Fish And Wildlife Service- Fws, It Goods
Brush Cutter/ Stump Grinder
NC- ALLIGATOR RIV NWR- MULCHER - Evaluation FactorsFactor 1 Technical Acceptability ( Pass/Fail) The Government will evaluate the offeror¿ s quote to verify compliance with all requirements in the solicitation and requirements document. Pass: Quote meets all mandatory req
Hydraulic Mulcher 1 34 to 36 rotary disc hydraulic mulcher compatible with an amphibious caterpillar 308 07a cr mhe mini excavator with a power pack pony motor, quick attach boom, and grapple thumb. The power pack is a Supertrak SK80PP 74hp with a Cummins 2. 8 engine 45cc pump closed loop, 30gpm w max pressure of **** technical specifications: 1 34 to 36 rotary disc hydraulic mulcher must be suitable for clearing brush, shrubs, standing trees, stumps, logs, etc. Heavy duty and durable construction capable of heavy daily use over extended periods. Cutting disc: 34 to 36 inch diameter, 1 1/4 thick Weldox 700 T1 steel or comparable. Weight: 1, 100 - 1, 400 lbs. Hydraulic flow: 26 to 37 gpm or comparable. Hydraulic pressure: 4, 100 psi working up to 6, 000 psi or comparable. Performance motor: bent axis piston hydraulic motor with anti- cavitation or comparable. Drive system: direct drive, oil bath bearing box, no belts or pulleys or comparable. Performance excavator size: must fit 8 to 10 ton excavator
Bid Close Date:
Commonwealth Of Kentucky - Transportation - Office Of The Secretary- KY
Eq Rental with operator D4 - State
Bid Close Date:
Lot 18: Rental of a tree and brush cutting/mulching attachment mounted on a large standard excavator with operator. Attachment shall be capable of grinding up to a 18 inch diameter tree including stump to ground level and have the capability to mulch debris. Attachment shall be mounted on a large excavator with a minimum operating weight of 44, 000 pounds. Total weight of attachment shall be a minimum of 3, 500 pounds. Attachment shall also include a third boom with a material handler for additional reach and increased geometry. Material handler shall be capable of stacking material. Weight of cutting wheel shall be a minimum of 1, 000 pounds and maximum cutting wheel speed shall be 550 rpm to limit debris throwing. Cutting swath shall be a minimum 52 inches. Reach from center of excavator to tip of cutter bar shall be a minimum of 38 feet. The hourly rental rate price shall include the excavator, tree cutting/mulching attachment, and operator. To be Komatsu PC 200 LC8 w/Slashbuster HD 480 B
Lot 1: Equipment shall meet the following minimum requirements: 145 HP or greater with operator equipped with/dirt & rock bucket & grapple. This line item shall be used for all work paid using STATE funds. Brand & Model Bid: *** ONLY ONLINE BIDS WILL BE ACCEPTED FOR THIS RFB. *** Emailed and hard copies delivered by any method WILL NOT BE ACCEPTED. See attached document How to Respond to an Online Bid through the Kentucky Vendor Self Service site ( updated). pdf. Please enter contact person, phone number a, nd email in the Comments Section. Vendors should review and update, if necessary, all addresses and contact persons for their account prior to bid submission. This information will carry forward to a contract if awarded, therefore please ensure all information is correct.
Lot 2: Equipment shall meet the following minimum requirements: 145 HP or greater with operator equipped with hoe- ram/rock hammer/impact breaker, with **** or greater ft- lbf ( Impact Energy Class). This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 3: Equipment shall meet the following minimum requirements: 150- 190 HP with operator equipped with long boom 60 feet reach with 1 CY bucket. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 4: Truck with operator shall meet the following minimum requirements: for on highway use 15 cubic yards. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 5: Dozer Crawler with operator shall meet the following minimum requirements: 80 HP equipped with angle/tilt and corner cutting blade. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 6: Dozer Crawler with operator shall meet the following minimum requirements: 125 HP equipped with angle/tilt and corner cutting blade. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 7: Track with operator equipped with attachments ( bucket, forks, grapple, and milling). This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 8: Equipment shall meet the following minimum requirements 4 Lights, 30 feet tall, diesel powered. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 9: Telescoping Tree Trimmer with minimum 75' reach and 24" carbide tipped saw blade. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 10: Whole Tree Chipper capable of chipping up to a minimum of 20" diameter tree. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 11: Excavator attachment - grapple capable of rotating 360 degrees with a rake configuration. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 12: Excavator attachment - grapple capable of rotating 360 degrees with a rake configuration. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 13: Tandem Dump Truck with operator and a minimum 30 CY bed for highway use. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 14: Tandem Dump Truck with operator and a minimum 30 CY bed with Grapple Loader with a minimum 25' reach for highway use. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 15: Wheel Loader with operator, articulated 150- 199 HP with 3. 5 CY minimum bucket capacity. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 16: Motor Grader w/operator minimum 12 ft blade. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 17: State escort truck w/operator 4 Wheel Drive, minimum 3/4 ton truck equipped with flashing safety lights. This line item shall be used for all work paid using STATE funds. Brand & Model Bid:
Lot 18: Rental of a tree and brush cutting/mulching attachment mounted on a large standard excavator with operator. Attachment shall be capable of grinding up to a 18 inch diameter tree including stump to ground level and have the capability to mulch debris. Attachment shall be mounted on a large excavator with a minimum operating weight of 44, 000 pounds. Total weight of attachment shall be a minimum of 3, 500 pounds. Attachment shall also include a third boom with a material handler for additional reach and increased geometry. Material handler shall be capable of stacking material. Weight of cutting wheel shall be a minimum of 1, 000 pounds and maximum cutting wheel speed shall be 550 rpm to limit debris throwing. Cutting swath shall be a minimum 52 inches. Reach from center of excavator to tip of cutter bar shall be a minimum of 38 feet. The hourly rental rate price shall include the excavator, tree cutting/mulching attachment, and operator. To be Komatsu PC 200 LC8 w/Slashbuster HD 480 B
Lot 19: Rental of a track mulcher with operator. The mulcher shall be mounted on tracks and be capable of mulching downed material on level ground and steep slopes. Mulcher shall be able to mulch trees and vegetation up to 12 inches in diameter into a fine mulch. To be Rayco 260 or 360
Lot 20: Rental of a whole tree chipper with operator. Whole tree chipper shall be self- feeding and be capable of chipping whole trees up to 24 inches in diameter into a fine mulch. To be Bandit **** or ****
Lot 21: Rental of rotating tree shear with operator. Rotating tree shear equipment shall be a minimum of 90 HP and be equipped with a grapple and rotating tree shears /saw capable of downing trees up to 24 inches in diameter. To be John Deere 759 J or Komatsu PC 200 LC 8 w/Dymax
Commonwealth Of Kentucky - Transportation - Office Of The Secretary- KY
Eq Rental with operator D4 - Federal
Bid Close Date:
Lot 18: Rental of a tree and brush cutting/mulching attachment mounted on a large standard excavator with operator. Attachment shall be capable of grinding up to a 18 inch diameter tree including stump to ground level and have the capability to mulch debris. Attachment shall be mounted on a large excavator with a minimum operating weight of 44, 000 pounds. Total weight of attachment shall be a minimum of 3, 500 pounds. Attachment shall also include a third boom with a material handler for additional reach and increased geometry. Material handler shall be capable of stacking material. Weight of cutting wheel shall be a minimum of 1, 000 pounds and maximum cutting wheel speed shall be 550 rpm to limit debris throwing. Cutting swath shall be a minimum 52 inches. Reach from center of excavator to tip of cutter bar shall be a minimum of 38 feet. The hourly rental rate price shall include the excavator, tree cutting/mulching attachment, and operator. To be Komatsu PC 200 LC8 w/Slashbuster HD 480 B
Lot 1: Equipment shall meet the following minimum requirements: 145 HP or greater with operator equipped with/dirt & rock bucket & grapple. This line item shall be used for all work paid using Federal funds. Brand & Model Bid: *** ONLY ONLINE BIDS WILL BE ACCEPTED FOR THIS RFB. *** Emailed and hard copies delivered by any method WILL NOT BE ACCEPTED. See attached document How to Respond to an Online Bid through the Kentucky Vendor Self Service site ( updated). pdf. Please enter contact person, phone number and email in the Comments Section. Vendors should review and update, if necessary, all addresses and contact persons for their account prior to bid submission. This information will carry forward to a contract if awarded, therefore please ensure all information is correct.
Lot 2: Equipment shall meet the following minimum requirements: 145 HP or greater with operator equipped with hoe- ram/rock hammer/impact breaker, with **** or greater ft- lbf ( Impact Energy Class). This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 3: Equipment shall meet the following minimum requirements: 150- 190 HP with operator equipped with long boom 60 feet reach with 1 CY bucket. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 4: Truck with operator shall meet the following minimum requirements: for on highway use 15 cubic yards. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 5: Dozer Crawler with operator shall meet the following minimum requirements: 80 HP equipped with angle/tilt and corner cutting blade. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 6: Dozer Crawler with operator shall meet the following minimum requirements: 125 HP equipped with angle/tilt and corner cutting blade. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 7: Track with operator equipped with attachments ( bucket, forks, grapple, and milling). This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 8: Equipment shall meet the following minimum requirements 4 Lights, 30 feet tall, diesel powered. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 9: Telescoping Tree Trimmer with minimum 75' reach and 24" carbide tipped saw blade. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 10: Whole Tree Chipper capable of chipping up to a minimum of 20" diameter tree. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 11: Excavator attachment - grapple capable of rotating 360 degrees with a rake configuration. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 12: Excavator attachment - grapple capable of rotating 360 degrees with a rake configuration. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 13: Tandem Dump Truck with operator and a minimum 30 CY bed for highway use. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 14: Tandem Dump Truck with operator and a minimum 30 CY bed with Grapple Loader with a minimum 25' reach for highway use. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 15: Wheel Loader with operator, articulated 150- 199 HP with 3. 5 CY minimum bucket capacity. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 16: Motor Grader w/operator minimum 12 ft blade. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 17: State escort truck w/operator 4 Wheel Drive, minimum 3/4 ton truck equipped with flashing safety lights. This line item shall be used for all work paid using Federal funds. Brand & Model Bid:
Lot 18: Rental of a tree and brush cutting/mulching attachment mounted on a large standard excavator with operator. Attachment shall be capable of grinding up to a 18 inch diameter tree including stump to ground level and have the capability to mulch debris. Attachment shall be mounted on a large excavator with a minimum operating weight of 44, 000 pounds. Total weight of attachment shall be a minimum of 3, 500 pounds. Attachment shall also include a third boom with a material handler for additional reach and increased geometry. Material handler shall be capable of stacking material. Weight of cutting wheel shall be a minimum of 1, 000 pounds and maximum cutting wheel speed shall be 550 rpm to limit debris throwing. Cutting swath shall be a minimum 52 inches. Reach from center of excavator to tip of cutter bar shall be a minimum of 38 feet. The hourly rental rate price shall include the excavator, tree cutting/mulching attachment, and operator. To be Komatsu PC 200 LC8 w/Slashbuster HD 480 B
Lot 19: Rental of a track mulcher with operator. The mulcher shall be mounted on tracks and be capable of mulching downed material on level ground and steep slopes. Mulcher shall be able to mulch trees and vegetation up to 12 inches in diameter into a fine mulch. To be Rayco 260 or 360
Lot 20: Rental of a whole tree chipper with operator. Whole tree chipper shall be self- feeding and be capable of chipping whole trees up to 24 inches in diameter into a fine mulch. To be Bandit **** or ****
Lot 21: Rental of rotating tree shear with operator. Rotating tree shear equipment shall be a minimum of 90 HP and be equipped with a grapple and rotating tree shears /saw capable of downing trees up to 24 inches in diameter. To be John Deere 759 J or Komatsu PC 200 LC 8 w/Dymax
Search by what you sell
Find bids beyond an exact phrase.
Choose an example to see how smart search can help.
You supply: Office chairs
How a solicitation might describe it
Supply of ergonomic seating for administrative work
The seating is described by its use, without repeating the product name.
Smart search helps connect what you supply with different descriptions. Try it with your own products during the free trial.
Start free trialYou supply: Pest control
How a solicitation might describe it
Insect and rodent management services
A different expression describes a related service.
Smart search helps connect what you supply with different descriptions. Try it with your own products during the free trial.
Start free trialYou supply: Toilet paper
How a solicitation might describe it
Supply of two-ply bathroom tissue
Another description of the product, including a purchasing specification.
Smart search helps connect what you supply with different descriptions. Try it with your own products during the free trial.
Start free trialFictional examples to explain how it works. This example does not run a search.
Tell us what you supply and see bids right away
-
Start with your email
Enter your email to start the free trial. There are no automatic charges.
-
Tell us what your business supplies
Add your specific products or services and the locations you want to search. Your first monitoring group is created for you.
-
See matching bids right away
Matching bids appear as soon as you save your products and locations. Explore groups and email settings at your own pace.
For teams and integrations
User testimonials
Very good and accurate information about the tenders: consistent and precise.
I consistently received notifications about bids within the specific segment I chose to monitor. The system simplifies processes that used to be complex, offering a navigation experience that is easy, fast, and modern.
You see a lot of tenders; you get emails with the alerts.
Good information. All the information is very good!
I closed deals thanks to the information gathered by the search tool. There’s no need to research across multiple media outlets.
It encompasses all portals in one place.
Everything is perfect. They are a great help in finding bids relevant to our field of work. I really appreciate that the bids are sent directly to my email; it’s a huge help in identifying where I can contribute and what I can do.
All bids related to our product are captured by you and sent to us. In my opinion, it’s perfect—broad coverage and easy searches across the bid documents.
The idea of ​​using a keyword and sending the information by email is very good.
I am very satisfied; it's a very useful tool.
The tool is truly effective at scanning bid documents, efficiently delivering bids.
A very good platform.
I like the way they provide information with the greatest possible accuracy. I love that.
Why use BidHits for government bidding
Filter bids, save promising opportunities and ask questions about solicitation documents.
-
Filters and map
Filter by location, procurement type and value. View opportunities on the map to decide what deserves a closer look.
-
Favorites and notes
Save the bids that interest you and add private notes, so you can return to your review later.
-
Solicitation document assistant
Ask questions about documents the system can read. Check the answers against the solicitation documents and the official source.
Frequently asked questions
See how it works
Add what you sell, get scheduled alerts, open documents or the official page, and use filters by region and method.