Anneal Government Bids & RFPs

This is a combined synopsis/solicitation for commercial items for round bar, 6-inch diameter, aluminum bronze, ASTM B150/B150M-19, alloy ****, temper TQ55, in 5-foot continuous lengths. The solicitation is a 100% small business set-aside with a Lowest Price Technically Acceptable (LPTA) evaluation criterion. Offerors must be registered in SAM. Proof of traceability is required if not the manufacturer. Payment terms are Net 30 days after acceptance, with a preference for Government Purchase Card (GPC) or Wide Area Workflow (WAWF). Delivery is to Portsmouth Naval Shipyard. The closing date for quotes is March 24, 2026, 2 PM ET.

The contract is for a special stud, to be in accordance with Newport News Shipbuilding drawing 412 ****, item 2. The unit of issue is each. The contractor is required to provide one additional fastener for each uniquely identified heat lot of material in each shipment. Complete traceability must be maintained on this extra fastener. Material for parts requiring certification quantitative chemical and mechanical analysis is required for the parts listed below unless specifically stated otherwise: part special stud item 2 material QQ N 286, annealed and age hardened iaw MIL DTL **** certification certifications are required for the following tests on the items listed below. Additional testing on other piece parts if any per applicable drawings and specifications is still required, but certifications are only required as listed below. The contractor must maintain adequate records of all inspections and tests. The records must indicate the nature and number of observations made, the number and type of deficiencies found, the quantities approved and rejected and the nature of corrective action taken as appropriate. Inspection records must be traceable to the material inspected. The suppliers gages, measuring and test equipment must be made available for use by the government representative when required to determine conformance with contract requirements. When conditions warrant, the suppliers personnel must be made available for operations of such devices and for verification of their accuracy and condition. All documents and reference data applicable to this contract must be available for review by the government representative. Copies of documents required for government inspection purposes must be furnished in accordance with the instructions provided by the government representative. The government has the right to inspect at source, any supplies or services that were not manufactured or performed within the contractors facility. Such inspection can only be requested by or under authorization of the government representative. Any purchasing documents to a subcontractor must cite the applicable portions of the contractually invoked quality system e. g. calibration requirements, plus any product requirements that apply to the supplies being purchased. When the government elects to perform source inspection at the subcontractors facility, applicable purchase documents must be annotated with the following statement: A government inspection is required prior to shipment from your plant. Upon receipt of this order, promptly notify the government representative who normally services your plant so that appropriate planning for government inspection can be accomplished. If you do not have an assigned government representative, notify the nearest Defense Contract Management Agency (DCMA) office. In the event that a local government representative or DCMA office cannot be located, our purchasing agent should be notified immediately. The prime contractors program must include procedures to assess the capability of the prospective suppliers to produce the products or supply the services in accordance with the contract, prior to the issuance of any purchase document. Each sub tier supplier of material or services for items in section 3 of this contract must be subjected to a periodic review or audit by the prime to determine the continued capability of the supplier to control the quality of the products or services specified in the purchase order or contract. The prime contractor must ensure that the purchased product conforms to specified purchase requirements and this contract. The type and extent of control applied to the supplier and the purchased product must be dependent upon the effect of the purchased product on the end item represented by this contract. The prime contractor must evaluate the requirements of the contract and select suppliers based on their ability to supply the product in accordance with the prime contra

The contract is for a special stud, to be in accordance with Newport News Shipbuilding drawing 412 ****, item 2. The unit of issue is each. The contractor is required to provide one additional fastener for each uniquely identified heat lot of material in each shipment. Complete traceability must be maintained on this extra fastener. Material for parts requiring certification quantitative chemical and mechanical analysis is required for the parts listed below unless specifically stated otherwise: part special stud item 2 material QQ N 286, annealed and age hardened iaw MIL DTL **** certification certifications are required for the following tests on the items listed below. Additional testing on other piece parts if any per applicable drawings and specifications is still required, but certifications are only required as listed below. The contractor must maintain adequate records of all inspections and tests. The records must indicate the nature and number of observations made, the number and type of deficiencies found, the quantities approved and rejected and the nature of corrective action taken as appropriate. Inspection records must be traceable to the material inspected. The suppliers gages, measuring and test equipment must be made available for use by the government representative when required to determine conformance with contract requirements. When conditions warrant, the suppliers personnel must be made available for operations of such devices and for verification of their accuracy and condition. All documents and reference data applicable to this contract must be available for review by the government representative. Copies of documents required for government inspection purposes must be furnished in accordance with the instructions provided by the government representative. The government has the right to inspect at source, any supplies or services that were not manufactured or performed within the contractors facility. Such inspection can only be requested by or under authorization of the government representative. Any purchasing documents to a subcontractor must cite the applicable portions of the contractually invoked quality system e. g. calibration requirements, plus any product requirements that apply to the supplies being purchased. When the government elects to perform source inspection at the subcontractors facility, applicable purchase documents must be annotated with the following statement: A government inspection is required prior to shipment from your plant. Upon receipt of this order, promptly notify the government representative who normally services your plant so that appropriate planning for government inspection can be accomplished. If you do not have an assigned government representative, notify the nearest Defense Contract Management Agency (DCMA) office. In the event that a local government representative or DCMA office cannot be located, our purchasing agent should be notified immediately. The prime contractors program must include procedures to assess the capability of the prospective suppliers to produce the products or supply the services in accordance with the contract, prior to the issuance of any purchase document. Each sub tier supplier of material or services for items in section 3 of this contract must be subjected to a periodic review or audit by the prime to determine the continued capability of the supplier to control the quality of the products or services specified in the purchase order or contract. The prime contractor must ensure that the purchased product conforms to specified purchase requirements and this contract. The type and extent of control applied to the supplier and the purchased product must be dependent upon the effect of the purchased product on the end item represented by this contract. The prime contractor must evaluate the requirements of the contract and select suppliers based on their ability to supply the product in accordance with the prime contra