Junction Box Government Bids & RFPs

Lot 1: Partnering

Lot 2: Community Relations Support

Lot 3: Stormwater Compliance

Lot 4: Environmental Mitigation Compliance

Lot 5: Compliance with Migratory Bird Treaty Act

Lot 6: 404 Permit Compliance

Lot 7: Bid Document Escrow

Lot 8: Rideability

Lot 9: Price Adjustment for Bituminous Materials

Lot 10: Uniformed Off- Duty Law Enforcement Officer

Lot 11: Dewatering

Lot 12: Description UOM Qty

Lot 13: Mobilization/Demobilization

Lot 14: Clearing and Grubbing

Lot 15: Roadway Excavation

Lot 16: Channel Excavation

Lot 17: Earthwork for Retention Basins

Lot 18: Riprap, D50= 6 in

Lot 19: Riprap, D50= 9 in

Lot 20: Riprap, D50= 12 in

Lot 21: Grouted Riprap, D50= 12 in

Lot 22: Erosion Control, 9 in Sediment Wattle

Lot 23: Erosion Control, 20 in Sediment Wattle

Lot 24: Erosion Control, Inlet Protection

Lot 25: Erosion Control, Construction Entrance/Exit Gravel Pad

Lot 26: Erosion Control, Rock Mulch, Gradation C ( 1 in- 3 in)

Lot 27: Subgrade Preparation

Lot 28: Maintenance Road, FCD Det FCD201- 2

Lot 29: Aggregate Base Course

Lot 30: Asphalt Concrete Pavement ( Superpave 1/2 in Mix, High Traffic)

Lot 31: Asphalt Concrete Pavement ( Superpave 3/4 in Mix, High Traffic)

Lot 32: Portland Cement Concrete Pavement ( PCCP) 8 in Thick

Lot 33: Bituminous Tack Coat SS- 1h or CSS- 1h, Diluted

Lot 34: Pavement Replacement, MAG Det 200, T Top

Lot 35: Vertical Curb & Gutter, Type A, H= 6 in, MAG Det 220

Lot 36: Single Curb, Type B, MAG Det 222

Lot 37: Concrete Sidewalk, MAG Det 230

Lot 38: 30 ft R Directional Curb Ramp Attached SW Dual Ramp MAG Det 237- 1

Lot 39: Driveway Entrance, MAG Det 250- 1, Commercial/Industrial

Lot 40: Driveway 9 in Thick Class A Concrete

Lot 41: Driveway, City of Peoria Std Det PE- 251- 2

Lot 42: Adjust Exist Manhole Frame & Cover, MAG Det 422, Type A

Lot 43: Adjust Valve Box & Cover, MAG Det 391- 1- A

Lot 44: Remove Pipe, Backfill & Compact, D

Lot 45: Remove Headwall

Lot 46: Remove Concrete Curb & Gutter

Lot 47: Remove Scupper

Lot 48: Remove Sidewalk

Lot 49: Remove Sidewalk Ramps

Lot 50: Remove Post

Lot 51: Remove Junction Structure

Lot 52: Remove Gate

Lot 53: Remove Concrete Driveway

Lot 54: Remove Asbestos Cement Pipe

Lot 55: Remove Concrete Spillway

Lot 56: Remove and Salvage Street Light

Lot 57: Remove and Salvage Traffic Sign Assembly

Lot 58: Remove Pull Box

Lot 59: Remove Guardrail

Lot 60: Removal of Pavement

Lot 61: Remove Barbed Wire Fence

Lot 62: Remove Chain Link Fence

Lot 63: Remove Block Wall

Lot 64: Remove Traffic Pole Foundation

Lot 65: Remove and Salvage Traffic Signal Pole and Mast Arm

Lot 66: Remove and Salvage Traffic Signal Cabinet

Lot 67: Remove and Salvage Luminaire Mast Arm

Lot 68: Remove and Salvage Video Detection System

Lot 69: Relocate Water Meter, City of Glendale Det G- 642

Lot 70: New Water Meter and Service Line Tap, COP Std Det PE- 363

Lot 71: Traffic Control

Lot 72: Portable Concrete Barrier, PCB

Lot 73: Portable Concrete Barrier, ( LF Barrier/Day of Use)

Lot 74: Portable Concrete Barrier Relocation

Lot 75: Impact Attenuation Device

Lot 76: Impact Attenuation Device, ( Each Device/Day of Use)

Lot 77: Impact Attenuation Device Relocation

Lot 78: Truck Mounted Attenuator

Lot 79: Changeable Message Board for Public Notification ( Each Board/Day of Use)

Lot 80: Survey Marker, Type A, MAG Det 120

Lot 81: Furnish and Install Barrier Attenuator

Lot 82: 6 ft Chain Link Fence, Type 1, ADOT C- ****

Lot 83: 6 ft x 24 ft Chain Link Fence Gate, MAG Det 160

Lot 84: Barbed Wire Fence, Type 1, ADOT C- ****

Lot 85: Plant - 24 in Box

Lot 86: Shrubs - 5 gal

Lot 87: Accent - 5 gal

Lot 88: Decomposed Granite, 2 in Thick, MAG Det 607- 1

Lot 89: Decomposed Granite, 2 in Thick, Match Existing

Lot 90: 3 in Sch 40 PVC Irrigation Pipe Sleeve

Lot 91: 6 in Sch 40 PVC Irrigation Pipe Sleeve

Lot 92: 1 in Drip Remote Control Valve Assembly ( Peoria)

Lot 93: Single Port Pressure Compensating Emitter ( Peoria)

Lot 94: Multi Port Pressure Compensating Emitter ( Peoria & Glendale)

Lot 95: 1- 1/2 in Reduced Pressure Backflow Assembly & Enclosure ( COG G- 669 & G- 673)

Lot 96: Sch. 40 PVC Irrigation Pipe 3/4 in

Lot 97: Sch. 40 PVC Irrigation Pipe 1- 1/2 in

Lot 98: Battery Operated Irrigation Controller

Lot 99: 4 in White Traffic Paint Stripe

Lot 100: 4 in Yellow Traffic Paint Stripe

Lot 101: 4 in White Thermoplastic Traffic Stripe

Lot 102: Thermoplastic/Preformed Symbol Lane Reduction Arrow

Lot 103: Thermoplastic/Preformed Symbol Left Turn Arrow

Lot 104: Thermoplastic/Preformed Symbol Right Turn Arrow

Lot 105: Reflectorized Raised Pavement Marker ( Type D, Yellow, 2- Way)

Lot 106: Reflectorized Raised Pavement Marker ( Type G, Clear, 1- Way)

Lot 107: Perforated Sign Post

Lot 108: Perforated Sign Post Foundation, Det ****

Lot 109: Flat Sheet Aluminum Sign Panel, High Intensity Grade

Lot 110: No. 5 Pull Box

Lot 111: No. 7 Pull Box with Extension

Lot 112: Sch. 40 PVC Electrical Conduit 1 in w/1/4 in Nyl PR # 8 Bare Copper Wire Trench

Lot 113: Sch. 40 PVC Elec. Cond. 2 in w/1/4 in Nyl PR # 8 Bare Copper Wire Trench

Lot 114: Sch. 40 Galvanized Electrical Conduit 2 in

Lot 115: Sch. 40 PVC Elec. Cond. 2 1/2 in with 1/4 in Nyl PR # 8 Bare Copper Wire Trench

Lot 116: Sch. 40 PVC Elec. Cond. 3 in with 1/4 in Nyl PR # 8 Bare Copper Wire Trench

Lot 117: Sch. 40 PVC Elec. Cond. 3 in w/1/4 in Nyl PR # 8 Bare Copper Wire HDD

Lot 118: Pole Foundation, Type PE05D, Peoria Det PE- 080- 10

Lot 119: Pole Foundation, Type PEO14D, Peoria Det PE- 080- 10

Lot 120: Pole Foundation, City of Glendale Det F- 1

Lot 121: Pole Foundation, Type G ( ADOT Std Dwg T- SL 4. 07, or COP PE- 150)

Lot 122: P Cabinet Foundation, Peoria Det PE- 083- 2

Lot 123: Traffic Control Cabinet Courtesy Pad ( Det PE- 082) ( City of Peoria)

Lot 124: Video Image Detection System, 2 Approaches

Lot 125: Signal Pole, Type PEO5D 10 ft, Peoria Det PE- 080- 09

Lot 126: Signal Pole, Type G, ADOT Std Dwg T- SL 4. 07

Lot 127: Streetlight Pole, City of Glendale Std Dwg P1

Lot 128: Signal Pole, Type PEO14D, Peoria Det PE- 080- 2

Lot 129: 40 ft Mast Arm

Lot 130: Electrical Service Pedestal System ( Lighting)

Lot 131: Controller Cabinet Assembly. Peoria Det PE- 083- 2

Lot 132: Fire Pre- emption Equipment

Lot 133: Signal Indication Type F Signal Face Type II Plumbizer Mount Asm Det **** Instal

Lot 134: Signal Indication Type F Signal Face Type Sky Mount

Lot 135: Signal Indication Type F Signal Face Type VII Mount Asm Det ****

Lot 136: Signal Indication Type G Signal Face Type XI Side Mount Asm Det ****

Lot 137: Signal Indication Type G Signal Face Type II Plumbizer Mount Asm Det ****

Lot 138: Signal Ind Type G Signal Face Type II Plumbizer Mount Asm Det **** Install Only

Lot 139: Signal Indication Type F Mod Signal Face Type XI Side Mount Asm Det ****

Lot 140: Signal Indication Type F and Type Q Signal Face Type VII Mount Asm

Lot 141: Pedestrian Signal Indication Type V Mount Asm Det ****

Lot 142: ADOT Type II Barrier Mounted Junction Box ( ADOT Std Det SD 1. 30)

Lot 143: Luminaire, Mast Arm 20 ft

Lot 144: Luminaire Mast Arm, 18 ft, ( ADOT Std Dwg T- SL 4. 29)

Lot 145: Luminaire Mast Arm, 12 Ft by 8 Ft, City of Glendale Det A6

Lot 146: LED Luminaire, Horizontal Mount ( GE Evolve ERL2- 0- 19- C3- 30- A- Gray w/PEC)

Lot 147: LED Luminaire, Horizontal Mount ( Atbhn ATBM- P10- MVOLT- R2- 3K- MP- NL- P7- ****

Lot 148: LED Luminaire, Underdeck ( W4GLED- ****- 30K- T3M- MVOLT- SPD- P7- BZSPD)

Lot 149: Internally Illuminated Street Name Sign

Lot 150: Electrical Conductors ( Streetlighting)

Lot 151: Electrical Conductors ( TS- Northern/103rd Ave)

Lot 152: Electrical Conductors ( New River Trail Underdeck Lighting)

Lot 153: ITS Pull Box ( COP Detail PE- 071)

Lot 154: ITS Type B Pull Box Det ****- 2

Lot 155: ITS Type E Pull Box Det ****

Lot 156: ITS Type E ( Split) Pull Box

Lot 157: 3- 3 in PVC Fiber Optic Conduits with # 8 Copper Wire ( Modified Det ****)

Lot 158: 4- 1 1/4 in PVC Fiber Optic Cond. w/# 12 Copper Wire ( Trench), Peoria Det PE- 070

Lot 159: Fiber Optic Cable, Single Mode 12

Lot 160: Fiber Optic Cable, Single Mode 144

Lot 161: CCTV with Quadcam

Lot 162: Concrete Scupper, MAG Det 206, S/W= 6 ft, 2- 4 ft Curb Opening

Lot 163: Concrete Scupper Spillway, MAG Det 206, 2- 4 ft Curb Opening

Lot 164: Concrete Scupper Spillway, MAG Det 206, 3- 4 ft Curb Opening

Lot 165: Concrete Scupper, MAG Det 206, S/W= 8 ft, 2- 4 ft Curb Opening

Lot 166: Concrete Scupper Spillway, MAG Det 206, 5- 4 ft Curb Opening

Lot 167: Concrete Scupper, MAG Det 206, S/W= 8 ft, 3- 4 ft Curb Opening

Lot 168: Concrete Scupper, MAG Det 206, S/W= 8 ft, 5- 4 ft Curb Opening

Lot 169: Double Catch Basin, ADOT C- ****, Modified

Lot 170: Triple Catch Basin, ADOT C- ****, Modified

Lot 171: Catch Basin, MAG Det 542- 1, Type M- 1, L= 17 ft

Lot 172: Sediment Trap, MAG Det OROW- 511

Lot 173: Concrete Junction Box, 1- 48 in ( in) 2- 36 in ( out), Special Det D2

Lot 174: Bollard, Type 1, 6 in Diameter, MAG Det 140

Lot 175: Safety Rail, Height 3 ft - 6 in, MAG Det 145

Lot 176: Headwall, Det ****, Straight Type, 18 in Pipe, Modified

Lot 177: Headwall, Det ****, Straight Type, 2- 30 in Pipe, Modified

Lot 178: Headwall, Det ****, U Type, 18 in Pipe, Modified

Lot 179: Headwall, Det ****, U Type, 24 in Pipe, Modified

Lot 180: Headwall, Det ****, U Type, 36 in Pipe, Modified

Lot 181: Headwall, Drop Inlet, MAG Det 501- 5, 18 in Pipe, Modified

Lot 182: Headwall, Drop Inlet, MAG Det 501- 5, 24 in Pipe, Modified

Lot 183: Headwall, Drop Inlet, MAG Det 501- 5, 48 in Pipe, Modified

Lot 184: Inlet with Trash Rack, 18 in Pipe, MAG Det 502- 1

Lot 185: Outlet Barrier Gate for 24 in Pipe, ADOT Std. Det C- ****

Lot 186: Outlet Barrier Gate for 36 in Pipe, ADOT Std. Det C- ****

Lot 187: Inlet with Trash Rack, 24 in Pipe, MAG Det 502- 1

Lot 188: Inlet with Trash Rack, 48 in Pipe, MAG Det 502- 1

Lot 189: Headwall, Outlet, Special Detail

Lot 190: 12 in Ductile Iron Pipe Waterline with Fittings

Lot 191: 12 in Ductile Iron Pipe Waterline with Fittings ( On Structure)

Lot 192: Install 12 in ACP to DIP Coupling, Glendale Approved Products

Lot 193: Remove Existing Fire Hydrant and Replace, Peoria Det PE- 360

Lot 194: Remove Existing Fire Hydrant and Relocate, Glendale Det G- 660

Lot 195: 12 in Cap on Existing Waterline, per MAG Section ****

Lot 196: Pipe Plug, MAG Det 427, 18 in Pipe

Lot 197: Pipe Plug, MAG Det 427, 36 in Pipe

Lot 198: Concrete Pipe Collar for 24 in Pipe, MAG Det 505

Lot 199: 18 in RGRCP, Class IV

Lot 200: 24 in RGRCP, Class IV

Lot 201: 30 in RGRCP, Class IV

Lot 202: 36 in RGRCP, Class IV

Lot 203: 48 in RGRCP, Class IV

Lot 204: Storm Drain Manhole, MAG Det 520 & 522

Lot 205: Storm Drain Outlet, ADOT Det C- ****

Lot 206: Drywell, MaxWell Plus or Equal, Basic Depth 30 ft

Lot 207: 12 in Gate Valve with Box & Cover

Lot 208: Install New Air Release Valve, City of Glendale Detail G- 646

Lot 209: Provide Water Service ( 1- 1/2 in)

Lot 210: Contractor Quality Control

Lot 211: Construction Surveying and Layout ( Heavy)

Lot 212: Construction Surveying and Layout ( Highway)

Lot 213: Structural Excavation

Lot 214: Structural Backfill

Lot 215: Drilled Shaft Foundation, 6. 5 ft Diameter

Lot 216: Drilled Shaft Foundation, 8 ft Diameter

Lot 217: Structural Concrete ADOT Class S, fc= **** PSI

Lot 218: Structural Concrete ADOT Class S, fc= **** PSI

Lot 219: Reinforcing Steel

Lot 220: Restrainer, Vertical Expansion

Lot 221: Restrainer, Fixed

Lot 222: Bridge Deck Joint Assembly Strip Seal

Lot 223: Reinforced Concrete Approach Slab

Lot 224: Precast/Prestressed Concrete Beam ( Bulb Tee 50 in)

Lot 225: Elastomeric Bearing Pads

Lot 226: Utility Hanger Support System

Lot 227: 12 in Water Pipe Hanger Support System

Lot 228: 20 in Sewer Casing Hanger Support System

Lot 229: Vehicular Barrier

Lot 230: Ped Curb without Fence

Lot 231: Bridge - Painting

Lot 232: Bridge - Metal Panels at Columns

Lot 233: Bridge - Pedestrian Barrier Steel Fencing

Lot 234: Bridge - Vehicular Barrier Steel Fencing

Lot 235: Bridge - Sandblasting

Lot 236: Support of Excavation ( SOE), Earthwork, Backfill

Lot 237: Disposal, Non- Hazardous

Lot 238: Steel Casing Pipe Sleeve, ASTM A- 283 Grade C, 20 in Dia. x **** in Thick

Lot 239: Epoxy- Coated Steel Spacers for Casing Pipe

Lot 240: 12 in HDPE

Lot 241: 12 in HDPE Fittings

Lot 242: Valve Vault for Combination Air Release/Vacuum Valve

Lot 243: Connection to Existing Manhole

Lot 244: Internal Drop Connection for Existing Manhole

Lot 245: Combination Air Release/Vacuum Valve

Lot 246: Subgrade Preparation

Lot 247: Aggregate Base Course

Lot 248: Asphalt Concrete Pavement ( Superpave 3/4 in Mix, High Traffic)

Lot 249: Vertical Curb & Gutter, Type A, H= 6 in, MAG Det 220

Lot 250: Headwall, Det ****, U Type, 18 in Pipe

Lot 251: 18 in RGRCP, Class IV

Lot 252: Headwall, MAG 501- 5

Lot 1: Electrician ONLY ONLINE BIDS WILL BE ACCEPTED FOR THIS RFB. Emailed and hard copies delivered by any method WILL NOT BE ACCEPTED. See section 1. 00 for Specifications. See attached document How to Respond to an Online Bid through the Kentucky Vendor Self Service site ( updated). pdf. A maximum hourly rate has been set for this line item. The unit price shall not exceed $ **** pay shall be paid to licensed electricians and to employees performing electrical work under the supervision of a licensed electrician. See invoicing and field sheets for common examples where unlicensed employees would be paid electrician pay. NOTE: This line will also be used to pay for permit applications. The quantity of hours to be paid for the completion of the application shall be mutually agreed upon by both parties.

Lot 2: Laborer A maximum hourly rate has been set for this line item. The unit price shall not exceed $ ****.

Lot 3: Equipment Operator A maximum hourly rate has been set for this line item. The unit price shall not exceed $ ****.

Lot 4: Service Vehicle Unit shall be capable of transporting equipment, tools, and individuals. This can only be billed when: Travelling to Central Office warehouse to pick up or drop- off materials, or Transporting materials from Central Office warehouse to the district, or Employees are being paid hourly and there is no other equipment ( Line Items 5- 11) that is eligible for reimbursement at an hourly rate. Approval of Project Manager is required, prior to starting work, if more than one service vehicle is required for hourly work.

Lot 5: 30' Bucket Truck Unit shall have a working height of thirty ( 30) feet.

Lot 6: 50' Bucket Truck Unit shall have a working height of fifty ( 50) feet.

Lot 7: Skid Steer Loader Unit shall be minimum of 80 HP and equipped with a bucket and shall include transporting of this item.

Lot 8: Flatbed Truck Unit shall be three quarter ton to five ton.

Lot 9: Air Compressor Unit shall have tools including jackhammer and shall include transporting of this item.

Lot 10: Aerial Lift Device Unit shall be capable of lifting personnel to a height of 130 ft Unit shall be capable of lowering and erecting high mast lighting structures up to 120 in height. If item needs to be transported, this is incidental to this item.

Lot 11: 1 1/2 Ton Line Truck Unit shall be equipped with 9", 18", 24", and 36" rock augers. Unit shall also include a pole trailer that carries a 45' pole.

Lot 12: Furnish and Install Conduit - 1/2 inch to 1 Inch Rigid Steel Furnish and Install Conduit 1/2 Inch to 1 Inch Rigid Steel

Lot 13: Furnish and Install Conduit - 1 1/4 Inch Rigid Steel

Lot 14: Furnish and Install Conduit 2 Inch Rigid Steel

Lot 15: Furnish and Install Conduit 2 1/2 Inch to 4 Inch Rigid Steel

Lot 16: Furnish and Install Conduit 1/2 Inch to 1 Inch PVC

Lot 17: Furnish and Install Conduit 1 1/4 Inch PVC

Lot 18: Furnish and Install Conduit 2 Inch PVC

Lot 19: Furnish and Install Conduit 2 1/2 Inch to 4 Inch PVC

Lot 20: Furnish and Install Conduit 3/4 inch to 2 Inch Flex Flexible Conduit

Lot 21: Wire- # 4 or Smaller ( Does not include Loop Wire)

Lot 22: Wire - # 2 or Larger

Lot 23: Wire- Loop Wire ( IMSA 51- 7)

Lot 24: Signal Cables 3C, 5C, and 7C ( IMSA 19 1) Cable

Lot 25: Loop Lead- In Cable ( IMSA 19- 2)

Lot 26: Cable - Multi- Conductor Item may include but is not limited to RG- 213, RG- 58, RG- 59, fiber optic cable, Belden ****, Belden ****, Belden ****, PE- 22, PE- 38, Plenum, EIA/TIA Plenum Rated or approved equals.

Lot 27: Span Wire 10, 800 LB /**** LB or Similar Span wire shall include the installation of the span wire and any associated hardware necessary for proper installation. This item requires the Contractor to furnish the following items: insulators, clevices, I- Bolts, and any other similar hardware. The Cabinet will furnish the following items: messenger cable, strandvices, splices, pole collars ( existing and new), bull rings, rock anchors, anchors, guide guard, and cable rings. The Contractor is responsible for installing noted Cabinet furnished items. Contractor shall be responsible to bond all span wires to comply with the NEC for Equipment grounding and supply connectors for this.

Lot 28: Cabinet Model 332 Base- Mounted

Lot 29: Cabinet Model 336 Pole- Mounted

Lot 30: Enclosure - Other Enclosure - Other shall include flasher, RWIS, DMS, and other metal or fiberglass enclosures from 6" x 6" x 6" up to 24" x 24" x 10".

Lot 31: Install Base Mounted Lighting Cabinet

Lot 32: Install Pole Mounted Lighting Cabinet

Lot 33: Pole 35 Feet to 55 Feet Wooden

Lot 34: Steel Pole up to 45 Feet ( includes MAST Arms)

Lot 35: Pole Steel 46 Feet to 120 Feet

Lot 36: Pole - Pedestal

Lot 37: Tower Aluminum 20 Feet to 40 Feet This is an install only line. Pole will be provided to Contractor and it could be up to 4 sections.

Lot 38: Furnish and Install Base Steel Pole from 46 Feet to 120 Feet

Lot 39: Furnish and Install Base Steel Pole Up to 45 Feet

Lot 40: Furnish and Install Base: Pedestal Four ( 4) foot deep including # 6 vertical bars and # 3 tie/spiral bars.

Lot 41: Furnish and Install Pad: Cabinet, Enclosure or Tower Payment for pads shall be based on the number of cubic yards of concrete required for installation, rounded up to the nearest tenth of a yard.

Lot 42: Furnish and Install Base - Luminaire

Lot 43: Traffic Signal Head Traffic signal shall include the installation of any specified signal head up to a five section signal head. This item includes but is not limited to the installation or building of any hangers, brackets, tethers, backplates and any other hardware required. The contractor shall furnish and install a rubber grommet in drilled hole. This item includes the installation of LED modules in the signal housing and the installation of wiring from LED modules to internal terminal strap. If replacing an existing traffic signal, the removal of the existing head is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks. Contractor shall be responsible to bond all metal components to comply with the NEC for Equipment grounding and supply connectors for this.

Lot 44: Pedestrian Signal Pedestrian signal shall include installation of specified signal head. Also included in this item shall be the installation of any material such as banding, brackets and other hardware needed to install the signal head to a wooden pole, steel strain pole, mast arm pole or pedestrian pole. The drilling of holes in poles for installation of wire shall be incidental to this item. The contractor shall furnish and install a rubber grommet in drilled hole. This item includes the installation of LED modules in the signal housing and the installation of wiring from LED modules to internal terminal strap. . If replacing an existing pedestrian signal, the removal of the existing head is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks. Contractor shall be responsible to bond all metal components to comply with the NEC for Equipment grounding and supply connectors for this

Lot 45: Pedestrian Push- Button Pedestrian push- button shall include the installation of a push- button. Included with this item shall be the installation of any hardware necessary for attachment of the push- button to a wooden pole, steel strain pole, mast arm pole or pedestrian pole. Also included is the installation of a pedestrian sign ( if required). The Contractor shall furnish and install bolts or screws for the attachments of push- buttons or signs. The drilling of holes in poles for installation of wire shall be incidental to this item. The contractor shall furnish and install a rubber grommet in drilled hole. If replacing an existing pedestrian push button, the removal of the existing head is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks. Contractor shall be responsible to bond all metal components to comply with the NEC for Equipment grounding and supply connectors for this

Lot 46: Accessible Pedestrian Push- Button Accessible pedestrian push- button shall include the installation of the push- button, the module in the pedestrian signal head, the wiring between the detector and the module, the termination of all wires and any other hardware necessary for proper installation. The Contractor shall furnish and install bolts or screws for the attachments of push- buttons or signs. The wire from the controller cabinet to the module and any conduit necessary shall be paid for separately. The drilling of holes in poles for installation of wire shall be incidental to this item. The contractor shall furnish and install a rubber grommet in drilled hole. If replacing an existing push button, the removal of the existing head is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks. Contractor shall be responsible to bond all metal components to comply with the NEC for Equipment grounding and supply connectors for this.

Lot 47: Signal- Electrical Service ( Signal, Beacons, School Flashers, and LED Blinker sign) Blinker sign Electrical service shall include installing safety switch ( s) and meter base on cabinet, pole or other specified structure in accordance with local utility requirements, and connection of service wire to equipment. This item includes the installation conduits ( weatherheads) and wiring from the utility service wiring to the bottom of the service disconnect. All conduits, grounding system, and wiring from bottom of disconnect shall be billed with separate items. The cabinet shall pay any electrical and/or inspection fees. The Cabinet as part of the initial electrical bill will pay any line extension construction costs. This item does include any labor hours and equipment hours required to meet with the utility company representative and locate poles, deliver inspection certificates, and otherwise coordinate the installation of the service. This item includes that the contractor furnishing and installing conduits used for grounding and service run ( this is up to 2 foot pass the base edge or pole). If replacing an existing service, the removal of the existing service is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 48: Ground Rod ( Singal & Lighting) Ground rod shall include installing a 5/8" x 8' copper clad steel ground rod in accordance with plans and specifications. This item includes the installation of any hardware or welding required for attachment of the ground wire to the ground rod. This item includes restoration of disturbed areas to original condition. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks

Lot 49: Furnish/Install Lighting HighMast Ground rod shall include furnishing and installing a 3/4" x 10' copper clad steel ground rod in accordance with plans and specifications. This item includes furnishing and installing of any hardware or welding required for attachment of the ground wire to the ground rod. This item includes restoration of disturbed areas to original condition. This includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 50: Junction Box Junction box shall include the installation of a composite concrete junction box as required. This item includes excavation ( includes rock), furnishing, and installing drainage aggregate (# 57) in accordance with KYTC specifications. This item includes furnishing and installing fiber fabric type IV in accordance with KYTC Specifications. This item includes restoration of disturbed areas to original condition. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 51: Junction Box Type B Junction box shall include the installation of a composite concrete junction box as required. This item includes excavation ( includes rock), furnishing and installing drainage aggregate (# 57) in accordance of KYTC specifications. This item includes furnishing and installing fiber fabric type IV in accordance of KYTC Specifications. This item includes restoration of disturbed areas to original condition. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 52: Loop Saw Slot and Fill Loop saw and slot fill shall include cutting and cleaning loop slot, drilling the transition to junction box/pole ( includes furnishing and installing conduit for the transition to the junction box/pole, cannot use conduit bid item), and furnishing and installing sealant, backer rod and grout. Any materials used to cut the slot shall be furnished by the contractor. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 53: Trenching and Backfilling Trenching and backfilling shall include 8 wide excavation, backfilling and the restoration of disturbed areas. This item shall include all equipment and tools required for trenching in any environment including solid rock. This item includes labor and equipment required for clearing trees and brush prior to trenching. This item includes restoration of disturbed areas to original condition. All fill shall be approved by the Contract Manager before the fill is installed in the trench. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks. Inspection of the trenching shall be required before backfilled.

Lot 54: 2" Rigid Steel Roadway Conduit Crossing Roadway conduit crossing shall include labor and equipment required for installation of furnished rigid steel conduit under paved surface via pushing or open cutting. All open cutting shall be pre- approved by the contract manager. This item shall include saw cutting, excavation, pushing, backfilling and the restoration of disturbed areas. This item includes furnishing and installing reinforcing steel, concrete and asphalt as required. The furnishing of conduit is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 55: 3" to 4" Rigid Steel Roadway Conduit Crossing Roadway conduit crossing shall include labor and equipment required for installation of furnished rigid steel conduit under paved surface via pushing or open cutting. All open cutting shall be pre- approved by the contract manager. This item shall include saw cutting, excavation, pushing, backfilling and the restoration of disturbed areas. This item includes furnishing and installing reinforcing steel, concrete and asphalt as required. The furnishing of conduit is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 56: 2" Rigid Steel Directional Boring Directional boring shall include labor and equipment required to install furnished rigid steel conduit where trenching or pushing is not feasible. Equipment shall be capable of boring a hole under roadway to accommodate a 2 diameter steel pipe. This item includes excavation, equipment, labor, supporting tools and restoration of disturbed areas. The furnishing of conduit is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 57: 3" TO 4 " Rigid Steel Directional Boring Directional boring shall include labor and equipment required to install furnished conduit where trenching or pushing is not feasible. Equipment shall be capable of boring a hole under roadway to accommodate a 3" to 4" diameter steel pipe. This item includes excavation, equipment, labor, supporting tools and restoration of disturbed areas. The furnishing of conduit is included in this item. Conduit can be from 3- inch and 4- inch rigid steel conduit. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks

Lot 58: Luminaire Arm Luminaire arm shall consist of installing a luminaire arm on luminaire pole, wood pole, steel strain pole, or any other type of pole or structure specified. Arms may range in length from 12" to 20' or be a" C " type bracket. This item includes, but is not limited to, banding/banding straps ( provided by the Cabinet), welding and bolting ( Contractor shall provide the bolts) the arm to the pole, and any other hardware necessary for installation. If removing an existing luminaire arm from a pole or structure, the removal shall be included in the installation of the new luminaire arm. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 59: Luminaire - Cobra - Head or Offset

Lot 60: Luminaire - High Mast

Lot 61: Luminarie - Wall or Ceiling Mounted

Lot 62: Luminaire - Navigation /Aviation

Lot 63: Fused Connector Fused connector shall include installing one connector kit as well as installing the proper fuse in the connector. If replacing an existing fused connector, the removal of the existing fused connector is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 64: Replacement of Luminaire Bulb /LED Replacement of luminaire bulb shall Include the installation and replacement of any type of bulbs, LEDS, starters, drivers, and ballast kits for conventional or high mast luminaires. If replacing any existing items stated above, the removal of the existing items is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 65: Install Above Ground Sensor Above Ground Sensor shall include installing a sensor on pole, mast arm, cabinet, or other structure. Sensor may consist of a video camera, radar sensor, acoustic sensor, radio/wireless router antenna, or other above ground sensing technology. The installation of cabling between module and above ground sensor shall be billed as cable multi conductor. This item includes installing brackets, banding, and other mounting hardware of the above ground sensor. If replacing an existing above ground sensor, the removal of the existing above ground sensor is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 66: Install Radio/Wireless Router/Telephone Modem/Above Sensor Module The radio/wireless router/telephone modem/above ground sensor shall include installing a radio, wireless router, or telephone modem/above ground sensor module inside the cabinet or other structure. The installation of the radio, wireless router, or telephone modem/above ground sensor module shall include the installation of a power supply, surge protector, cabling between surge protector and radio, and cabling from radio/wireless router/telephone modem/above ground sensor module to any other device in the cabinet. If more than one of these items is installed, the installation shall be a separate billed item. The installation of cabling between radio/wireless router/telephone modem/above ground sensor module and above ground sensor shall be billed as cable/multi conductor. For new installations, the Contractor shall program radios, wireless routers, telephone modems, and above ground sensor module. If replacing an existing radio/wireless router/telephone modem/above ground sensor, the removal of the existing radio/wireless router/telephone modem/above ground sensor is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 67: Program Above Ground Sensor Module, Radio, Wireless Router, or Telephone Modem Program above ground sensor module, radio, wireless router, or telephone modem shall consist of programming existing video camera/module, radar sensor/module, acoustic sensor/module, radio, wireless router, telephone modem, or other above ground sensing technology. This item includes device aiming, programming, adjusting, and observation to verify proper operation. This includes ensuring that the contractor has the proper programming tools to do this task ( card programming and camera programming). This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 68: Install Sensor In Pavement This item shall include core drilling at least a 4" diameter by 2 1/2" depth hole in asphalt or concrete pavement for each sensor. This item includes the installation of at least 3 sensors per lane. This includes the installation of the sensor/cam shell and epoxy into the cored hole. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 69: Remove Sensor This item shall include removing the core drilling hole in asphalt or concrete pavement for each sensor. This item includes the removing of at least 3 sensors per lane. This item includes returning the sensor( s) to the Contract Manager. This item includes the installation of grout in the existing hole( s) in the pavement. The grout will be supplied by Cabinet. If the Contractor damages the sensor, the Contractor shall replace the sensor in kind at their cost. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 70: Sign - Install Sign shall consist of installing a sign on a span, mast arm, or other structure. This item includes, but is not limited to, the installation and building of hangers, brackets, tethers, and any other hardware necessary for installation. If replacing an existing sign, the removal of the existing sign is included in this item. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 71: Install LED Module ( Signal Head) Install LED module ( signal head) shall include installing one LED module in an existing signal head. This item may include removing the existing lens, reflector, lamp, LED module, and any other hardware that may need to be removed in order to install the new LED. This item also includes terminating any wires necessary for a professional and proper installation. If replacing an existing LED module, the removal of the existing LED module is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 72: Install LED Module ( Pedestrian Head) Install LED module ( pedestrian head) shall include installing one LED module in an existing pedestrian signal head. This item may include removing the existing lens, reflector, lamp, LED module, and any other hardware that may need to be removed in order to install the new LED. This item also includes terminating any wires necessary for a professional and proper installation. If replacing an existing LED module, the removal of the existing LED module is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 73: Furnish and Install 200 AMP Lighting Electrical Service ( 480 Volt Single Phase) Item shall include furnishing and installing a 200 AMP safety switch and meter base on channel/square posts, pole, or other specified structure in accordance with local utility requirements, and connection of service wire to equipment. This item includes the installation conduits ( weatherheads) and wiring from the utility service wiring to the bottom of the service disconnect. All conduits, grounding system, and wiring from bottom of disconnect shall be billed with separate items. The Cabinet shall pay any electrical and/or inspection fees. The Cabinet, as part of the initial electrical bill, will pay any line extension construction costs. This item includes any labor hours and equipment hours required to meet with the utility company representative and locate poles, deliver inspection certificates, and otherwise coordinate the installation of the service. This item includes the contractor furnishing and installing conduits used for grounding and service run ( this is up to 2 foot pass the base edge or pole). If replacing an existing service, the removal of the existing service is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 74: Furnish and Install Lighting Electrical Services ( 120/240 Volt) Item shall include furnishing and installing a 60 AMP safety switch and meter base on channel/square posts, pole or other specified structure in accordance with local utility requirements, and connection of service wire to equipment. This item includes the installation conduits ( weatherheads) and wiring from the utility service wiring to the bottom of the service disconnect. All conduits, grounding system, and wiring from bottom of disconnect shall be billed with separate items. The Cabinet shall pay any electrical and/or inspection fees. The Cabinet, as part of the initial electrical bill, will pay any line extension construction costs. This item includes any labor hours and equipment hours required to meet with the utility company representative and locate poles, deliver inspection certificates, and otherwise coordinate the installation of the service. This item includes the contractor furnishing and installing conduits used for grounding and service run ( this is up to 2 foot pass the base edge or pole). If replacing an existing service, the removal of the existing service is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 75: Furnish and Install Junction Box Type A Item shall include furnishing and installing a composite concrete junction box as specified by Cabinet specifications. This item includes excavation ( includes rock), furnishing, and installing drainage aggregate (# 57) in accordance with Cabinet specifications. This item includes furnishing and installing fiber fabric type IV in accordance of KYTC Specifications. This item includes restoration of disturbed areas to original condition. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 76: Furnish and Install Junction Box Type C Item shall include furnishing and installing of a composite concrete junction box as specified by Cabinet specifications. This item includes excavation ( includes rock), furnishing, and installing drainage aggregate (# 57) in accordance with Cabinet specifications. This item includes furnishing and installing fiber fabric type IV in accordance with KYTC Specifications. This item includes restoration of disturbed areas to original condition. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks

Lot 77: Furnish and Install 60 AMP to 100 AMP Lighting Electrical Services ( 480 VOLT SINGLE PHASE) Item shall include furnishing and installing a 60 AMP TO 100 AMP safety switch and meter base on channel/square posts, pole, or other specified structure in accordance with local utility requirements, and connection of service wire to equipment. This item includes the installation conduits ( weatherheads) and wiring from the utility service wiring to the bottom of the service disconnect. All conduits, grounding system, and wiring from bottom of disconnect shall be billed with separate items. The Cabinet shall pay any electrical and/or inspection fees. The Cabinet, as part of the initial electrical bill, will pay any line extension construction costs. This item includes any labor hours and equipment hours required to meet with the utility company representative and locate poles, deliver inspection certificates, and otherwise coordinate the installation of the service. This item includes the contractor furnishing and installing conduits used for grounding and service run ( this is up to 2 foot pass the base edge or pole). If replacing an existing service, the removal of the existing service is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 78: Install Transformer Base Only Install transformer base only shall include the installation of a transformer base on existing/new base only if the pole will be installed at a later time per the contract manager. This item includes the installation of all bottom hardware and a furnishing/installing an aluminum metal cover on the top of the transformer base for safety. The cabinet will furnish the transformer base and hardware for the t- base. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 79: Furnish and Install AC or Solar School Flasher This item includes furnishing and installing materials to build the structure that holds the school flasher assembly that is installed on a span, luminaire pole, pedestal pole, steel strain pole, or wood pole. The Contractor furnished school flasher assembly shall include brackets or pipes that mount the Cabinet supplied beacons and signs. All signal heads ( including LED module installation) and sign assembly shall be included in this item. The Cabinet shall supply signal heads, LED modules, signs, one way span hangers, and pole mounted hardware. The beacon cabinet ( item 30), conduits ( items 12- 20), electrical service ( item 44), grounding system ( item 45), and wire shall be billed separately. The contractor shall not bill for a traffic signal ( item 40) or sign ( item 58) when using this item. If replacing an existing school flasher stated above, the removal of the existing school flashers is included in this item. This item includes all equipment, labor, and electrician supervisor hours needed to perform these tasks.

Lot 80: Furnish and Install AC or Solar Blinker Sign This item includes furnishing and installing materials to build the structure that holds the blinker sign assembly, which is installed on a span, luminaire pole, pedestal pole, steel strain pole, or wood pole. The furnished blinker sign assembly shall include brackets or pipes that mount the KYTC supplied blinker signs. The Cabinet shall supply blinker signs, one way span hangers, and pole mounted hardware. The blinker cabinet ( item 30), conduits ( items 12- 20), electrical service ( item 44), grounding system ( item 45), and wire shall be billed separately. The contractor shall not bill for a sign ( item 58) when using this item. If replacing an existing item stated above, the removal of the existing items is included in this item. This includes all equipment, labor, and electrician supervisor hours to perform these tasks.

Lot 81: Move /Align Traffic Signal Head /Pedestrian/Sign This item includes furnishing and installing materials to build the structure that holds the blinker sign assembly, which is installed on a span, luminaire pole, pedestal pole, steel strain pole, or wood pole. The furnished blinker sign assembly shall include brackets or pipes that mount the KYTC supplied blinker signs. The Cabinet shall supply blinker signs, one way span hangers, and pole mounted hardware. The blinker cabinet ( item 30), conduits ( items 12- 20), electrical service ( item 44), grounding system ( item 45), and wire shall be billed separately. The contractor shall not bill for a sign ( item 58) when using this item. If replacing an existing item stated above, the removal of the existing items is included in this item. This includes all equipment, labor, and electrician supervisor hours to perform these tasks.

Lot 82: Remove and Reinstall Anchors Remove and reinstall anchors shall include the drilling/cutting of the existing anchor, furnishing/installing epoxy ( KYTC specified) in existing base. The cabinet will furnish the anchor bolt for this installation. This could include modification of supplied anchor bolt, and the contractor shall have the tools to modify. This item includes all equipment, labor and electrician supervisor hours needed to perform these tasks.

Lot 83: Tether Install Tether wire shall include the installation of the tether span wire any associated hardware necessary for proper installation. This item requires the Contractor to furnish the following items: insulators, clevises, I- Bolts, and any other similar hardware. The Cabinet will furnish the following items: messenger cable, strand vices, splices, pole collars ( existing and new), bull rings, rock anchors, anchors, guide guards, and cable rings. The Contractor is responsible for installing noted Cabinet furnished items.

Lot 84: Pole - Roadway Luminaire ( if a new/existing pole installation, this include attaching the arm and installing transformer base to the new/existing pole base)

Lot 85: On- Call A maximum hourly rate has been set for this line item. This item shall be the price for the contractor to put one electrician on call per hour. The unit price shall not exceed $ **** per electrician per hour. This contract requires two electricians to be on call if the Contract Manager puts the Contractor on call. On- call status requires that employees be present in the district. All expenses, such as hotel and meals, shall be incidental. Work vehicles shall be incidental to this item. Labor and equipment hours ( Lines 1- 11) shall not be billed for any individual utilizing the on- call bid item.

Lot 1: Unclassified excavation

Lot 2: Aggregate base

Lot 3: Dowell jointed p. C. C. Pavement 6 inch

Lot 4: Dowell jointed p. C. C. Pavement 8 inch

Lot 5: Drilled shafts 42 inch diameter

Lot 6: Drilled shafts 48 inch diameter

Lot 7: Drilled shafts 54 inch diameter

Lot 8: . 75- inch galvanized steel electrical conduit exposed

Lot 9: 1- inch galvanized steel electrical conduit exposed

Lot 10: 1. 25- inch galvanized steel electrical conduit exposed

Lot 11: 1. 5- inch galvanized steel elctrical conduit exposed

Lot 12: 2- inch galvanized steel electrical conduit exposed

Lot 13: 3- inch galvanized steel elctrical conduit exposed

Lot 14: 2- inch rigid plastic conduit ( bored)

Lot 15: 3- inch rigid plastic conduit ( bored)

Lot 16: 4- inch rigid plastic conduit ( bored)

Lot 17: 2- inch rigid plastic conduit ( trenched)

Lot 18: 3- inch rigid plastic conduit ( trenched)

Lot 19: 4- inch rigid plastic conduit ( trenched)

Lot 20: ( 3) conductor traffic signal electrical cable

Lot 21: ( 21) conductor traffic signal electrical cable

Lot 22: ( 5) conductor traffic signal electrical cable

Lot 23: ( 5) conductor traffic signal cable overhead

Lot 24: ( 7) conductor traffic signal electrical cable

Lot 25: ( 7) conductor traffic signal cable overhead

Lot 26: ( 9) conductor traffic signal electrical cable

Lot 27: ( 12) conductor traffic signal electrical cable

Lot 28: ( 15) conductor traffic signal electrical cable

Lot 29: ( 18) conductor traffic signal electrical cable

Lot 30: Two conductor shielded loop detector lead- in cable

Lot 31: Loop wire 14 awg ( type xhhw)

Lot 32: ( 1 conductor) ( awg no. 6) electrical conductor

Lot 33: ( 1 conductor) ( awg no. 10) electrical conductor

Lot 34: 1/c no. 4 thhn electrical conductor

Lot 35: 2/c no. 12 uf electrical conductor

Lot 36: 3/c # 4 aluminum conductors urd

Lot 37: 1 way 1 sec. Adj. Signal head

Lot 38: 1 way 3 sec. Adj. Signal head

Lot 39: 1 way 4 sec. Adj. Signal head

Lot 40: 1 way 5 sec. Adj. Signal head

Lot 41: Modular pedestrian signal head

Lot 42: Traffic signal backplate

Lot 43: Pedestrian push button and sign

Lot 44: 20- foot pole ( single 20 ft mast arm)

Lot 45: 20- foot pole ( single 25 ft mast arm)

Lot 46: 20- foot pole ( single 30 ft mast arm)

Lot 47: 20- foot pole ( single 35 ft mast arm)

Lot 48: 20- foot pole ( single 40 ft mast arm)

Lot 49: 20- foot pole ( single 45 ft mast arm)

Lot 50: 20- foot pole ( single 50 ft mast arm)

Lot 51: 20- foot pole ( single 55 ft mast arm)

Lot 52: 20- foot pole ( dual 20 ft mast arm)

Lot 53: 20- foot pole ( dual 25 ft mast arm)

Lot 54: 20- foot pole ( dual 30 ft mast arm)

Lot 55: 20- foot pole ( dual 35 ft mast arm)

Lot 56: 20- foot pole ( dual 40 ft mast arm)

Lot 57: 20- foot pole ( dual 45 ft mast arm)

Lot 58: 20- foot pole ( dual 50 ft mast arm)

Lot 59: 20- foot pole ( dual 55 ft mast arm)

Lot 60: 32- foot pole ( single 20 ft mast arm) and luminaire arm

Lot 61: 32- foot pole ( single 25 ft mast arm) and luminaire arm

Lot 62: 32- foot pole ( single 30 ft mast arm) and luminaire arm

Lot 63: 32- foot pole ( single 35 ft mast arm) and luminaire arm

Lot 64: 32- foot pole ( single 40 ft mast arm) and luminaire arm

Lot 65: 32- foot pole ( single 45 ft mast arm) and luminaire arm

Lot 66: 32- foot pole ( single 50 ft mast arm) and luminaire arm

Lot 67: 32- foot pole ( single 55 ft mast arm) and luminaire arm

Lot 68: 32- foot pole ( dual 20 ft mast arm) and luminaire arm

Lot 69: 32- foot pole ( dual 25 ft mast arm) and luminaire arm

Lot 70: 32- foot pole ( dual 30 ft mast arm) and luminaire arm

Lot 71: 32- foot pole ( dual 35 ft mast arm) and luminaire arm

Lot 72: 32- foot pole ( dual 40 ft mast arm) and luminaire arm

Lot 73: 32- foot pole ( dual 45 ft mast arm) and luminaire arm

Lot 74: 32- foot pole ( dual 50 ft mast arm) and luminaire arm

Lot 75: 32- foot pole ( dual 55 ft mast arm) and luminaire arm

Lot 76: Pedestal pole with 5- foot mounting height

Lot 77: Pedestal pole with 8- foot mounting height

Lot 78: Pedestal pole with 10- foot mounting height

Lot 79: Pedestal pole with 12- foot mounting height

Lot 80: Pedestal pole with 15- foot mounting height

Lot 81: Structural concrete

Lot 82: Reinforcing steel

Lot 83: Pull box type 1

Lot 84: Pull box type 2

Lot 85: Sheet aluminum signs

Lot 86: Mast arm mounted signs

Lot 87: Square steel sign post

Lot 88: Pavement marking removal ( plastic) ( 4- inch wide)

Lot 89: Pavement marking removal ( plastic) ( 6- inch wide)

Lot 90: Pavement marking removal ( plastic) ( arrows)

Lot 91: Traffic stripe ( stripe)( words)

Lot 92: Traffic stripe ( plastic)( symbols)

Lot 93: Remover traffic stripe ( 4- inch wide)

Lot 94: Remove traffic stripe ( 6- inch wide)

Lot 95: Remove traffic stripe ( arrow)

Lot 96: Remove traffic stripe ( words)

Lot 97: Remove traffic stripe ( symbols)

Lot 98: Structural removal ( traffic signal pole)

Lot 99: Structural removal ( mast arm)

Lot 100: Structural removal ( traffic signal pole foundation)

Lot 101: Structural removal ( traffic signal head)

Lot 102: Structural removal ( pedestrian signal head)

Lot 103: Structural removal ( pedestrian pole)

Lot 104: Structural removal ( light pole anchor bolts)

Lot 105: Structural removal ( controller cabinet)

Lot 106: Structural removal ( light pole)

Lot 107: Pavement removal ( p. C. Concrete)

Lot 108: Pavement removal ( asphalt)

Lot 109: Sidewalk removal

Lot 110: Curb and gutter removal ( all types)

Lot 111: Sidewalk ( 4 inches)

Lot 112: Tactile warning device

Lot 113: Curb and gutter all types

Lot 114: Radar detection system ( advance sensors)

Lot 115: Radar detection system ( presence sensors)

Lot 116: Radar cabinet interface ( arc)

Lot 117: Radar detector cable

Lot 118: Switch for existing traffic control cabinet

Lot 119: Modem only

Lot 120: Controller database conversion

Lot 121: Tsp ffirmware upgrade for 980 atc

Lot 122: Antenna ap- cc- q- 522- wh

Lot 123: Multimode phase selector model 764

Lot 124: Opticon preemption programming 980

Lot 125: Auxiliary panel model 768

Lot 126: **** gps radio unit with bracket

Lot 127: Gps cable

Lot 128: E. P. S. Optical detector

Lot 129: E. P. S. 2 channel phase selector

Lot 130: Optical detector cable

Lot 131: Junction box ( 6 inch by 6 inch by 4 inch)

Lot 132: Junction box ( 8 inch by 8 inch by 6 inch)

Lot 133: Junction box ( 12 inch by 12 inch by 8 inch)

Lot 134: Hand hole cover ( light pole)

Lot 135: Hand hole cover ( signal pole)

Lot 136: ( pl) liquid tight flexible conduit

Lot 137: Removal of exposed conduit

Lot 138: Sawcut pavement loops

Lot 139: Blankout sign

Lot 140: Alpha technologies stand alone ups system

Lot 141: Alpha cell 240xtv battery- 12v - 112ah - top m6

Lot 142: 20- foot pole coated as noted ( single 20- 40 foot arm)

Lot 143: 20- foot pole coated as noted ( dual 20- 40 foot arm)

Lot 144: 20- foot pole coated as noted ( single 45 foot+ arm)

Lot 145: 20- foot pole coated as noted ( dual 45 foot+ arm)

Lot 146: 32- foot pole and luminaire arm coated as noted ( single 20 - 40 foot arm)

Lot 147: 32- foot pole and luminaire arm coated as noted ( dual 20 - 40 foot arm)

Lot 148: 32- foot pole and luminaire arm coated as noted ( single 45 foot+ arm)

Lot 149: 32- foot pole and luminaire arm coated as noted ( dual 45 foot+ arm)

Lot 150: Anchor bolt set1. 5- inch

Lot 151: Anchor bolt set1. 75- inch

Lot 152: Anchor bolt set 2- inch

Lot 153: Engineered odot footing/base design for mast arms greater than 55 feet

Lot 154: 20- foot mast arm

Lot 155: 25- foot mast arm

Lot 156: 30- foot mast arm

Lot 157: 35- foot mast arm

Lot 158: 40- foot mast arm

Lot 159: 45- foot mast arm

Lot 160: 50- foot mast arm

Lot 161: 55- foot mast arm

Lot 162: 60- foot mast arm

Lot 163: 65- foot mast arm

Lot 164: 20- foot mast arm coated as noted

Lot 165: 25- foot mast arm coated as noted

Lot 166: 30- foot mast arm coated as noted

Lot 167: 35- foot mast arm coated as noted

Lot 168: 40- foot mast arm coated as noted

Lot 169: 45- foot mast arm coated as noted

Lot 170: 50- foot mast arm coated as noted

Lot 171: 55- foot mast arm coated as noted

Lot 172: 60- foot mast arm coated as noted

Lot 173: 65- foot mast arm coated as noted

Lot 174: 20 foot upright - 15 foot arm ( material only)

Lot 175: 20 foot upright - 20 foot arm ( material only)

Lot 176: 20 foot upright - 25 foot arm ( material only)

Lot 177: 20 foot upright - 30 foot arm ( material only)

Lot 178: 20 foot upright - 35 foot arm ( material only)

Lot 179: 20 foot upright - 40 foot arm ( material only)

Lot 180: 20 foot upright - 45 foot arm ( material only)

Lot 181: 20 foot upright - 50 foot arm ( material only)

Lot 182: 30 foot upright - 15 foot arm ( material only)

Lot 183: 30 foot upright - 20 foot arm ( material only)

Lot 184: 30 foot upright - 25 foot arm ( material only)

Lot 185: 30 foot upright - 30 foot arm ( material only)

Lot 186: 30 foot upright - 35 foot arm ( material only)

Lot 187: 30 foot upright - 40 foot arm ( material only)

Lot 188: 30 foot upright - 45 foot arm ( material only)

Lot 189: 30 foot upright - 50 foot arm ( material only)

Lot 190: 30 foot upright - 55 foot arm ( material only)

Lot 191: 15 foot mast arm ( material only)

Lot 192: 20 foot mast arm ( material only)

Lot 193: 25 foot mast arm ( material only)

Lot 194: 30 foot mast arm ( material only)

Lot 195: 35 foot mast arm ( material only)

Lot 196: 40 foot mast arm ( material only)

Lot 197: 45 foot mast arm ( material only)

Lot 198: 50 foot mast arm ( material only)

Lot 199: 55 foot mast arm ( material only)

Lot 200: Mpz panel ( electrical) ( material only)

Lot 201: Mpz cabinet ( electrical) ( material only)

Lot 202: Mpz electrical meter rack ( electrical)

Lot 203: Install mpz panel ( electrical)

Lot 204: Install mpz cabinet ( electrical)

Lot 205: T c b ii - 20 amp ( electrical)

Lot 206: T c b ii - 30 amp ( electrical)

Lot 207: Ge **** disconnect 200 amp 3 pole 240v nema 3r

Lot 208: Ge **** transformer

Lot 209: Square d - qo circuit breaker 1 pole 120v 30 amp

Lot 210: Square d - qo circuit breaker 1 pole 120v 20 amp

Lot 211: Square d - fa circuit breaker 2 pole 480v 60 amp

Lot 212: Ge electrical cr **** lighting contractor 12- pole

Lot 213: Ge 2pole 30a contactor modules

Lot 214: Intermatic **** photo cell

Lot 215: Tork time clock

Lot 216: Little fuse no. Wbpb1 boot & lebaa fuse holder

Lot 217: Little fuse no. Klk- r15 600v fuse

Lot 218: Illsco no. Ped3- 350ss- db

Lot 219: **** 60- INCH x 60- INCH x 24- INCH NEMA 4 ENCLOSURE POWDER COAT GE

Lot 220: ( ****) female cord body - 15 amp 125 volt nema 5- 15r 2p 3w connector

Lot 221: Removal of high mast tower

Lot 222: Install high mast tower

Lot 223: 130- foot high mast pole ( g. Stl. )

Lot 224: 140- foot high mast pole ( g. Stl. )

Lot 225: 150- foot high mast pole ( g. Stl. )

Lot 226: High mast lowering device type 1

Lot 227: Crane rental ( up to 150 foot)

Lot 228: Relocate traffic signal head

Lot 229: Cmc gel pak no dsr- 2k

Lot 230: Install light pole and fixture ( provided)

Lot 231: Light pole footing ( epoxy anchor bolts)

Lot 232: 30 foot light pole base and anchor bolts

Lot 233: 16 foot light pole base and anchor bolts

Lot 234: Light pole type 1 ( 16 foot pole)

Lot 235: Light pole type 2 ( 16 foot pole w/banner arms)

Lot 236: Light pole type 3 ( 30 foot pole)

Lot 237: Light pole type 4 ( 30 foot pole w/16 ped. Mounting bracket)

Lot 238: Light pole type 5 ( 30 foot pole w/16 ped mounting plate & banner arms)

Lot 239: Pull box adjustment

Lot 240: Remove existing sign

Lot 241: ( pl) reset of light pole

Lot 242: Remove fixture off existing pole

Lot 243: Install provided fixture onto existing pole

Lot 244: Pedestrin led- enhanced crossing warning sign ( solar)

Lot 245: Led - enhanced stop sign remove and replace

Lot 246: Double sided led enhanced pedesatrian crossing sign remoe and replace

Lot 247: Remove nd relocate school zone flashing warning sign

Lot 248: Complete szf assembly

Lot 249: Rg 58 cable

Lot 250: 9p- 9p cable

Lot 251: 16 foot x 4. 5 inch aluminum pole

Lot 252: Pole base collar

Lot 253: Pole caps

Lot 254: Verizon cell modem

Lot 255: Modem antenna

Lot 256: Cell modem antenna

Lot 257: Materials- cost plus 20%

Lot 258: Message board

Lot 259: Message board

Lot 260: Track access permit

Lot 261: Construction signing and traffic control interstate shoulder closure

Lot 262: Construction signing and traffic control interstate lane closure

Lot 263: Investigation rate

Lot 264: Electrician rate

Lot 265: Technician rate

Lot 266: Bucket truck with operator

Lot 267: Foreman truck

Lot 268: Apprentice rate

Lot 269: Concrete pavement ( paver underlayment)

Lot 270: Concrete unit paver

Lot 271: Remove and reset pavers

Lot 272: Radar/video hybrid detection

Lot 273: Video incident monitoring system