Latest US Bed Rails Contracts & Bids

The notice describes a request for a new blanket purchase agreement (BPA) for medical-grade specialty therapy beds with accessories. The procurement is a sole-source acquisition under FAR ****, following FAR ****, modified to reflect FAR subpart 13. 5 procedures. The medical readiness contracting office (MrCOW) seeks to establish a BPA call against a master BPA. The need is for the rental of medical-grade specialty therapy beds with accessories. The Brooke Army Medical Center has a need for the rental of this equipment.

The Office of State Procurement is seeking bids for a plasma cutting table. Bidders must be registered in the lagov system. The bid opening is on May 28, 2025 at 10:00 AM CST. The bid must be submitted online via the provided link. All required attachments must be included in the bid response. The bid must be manually signed in ink or submitted online via the vendor portal. The bid must include delivery, installation, and onsite training. The method of award is to the lowest responsive, responsible bidder meeting the specifications. A non-mandatory jobsite visit is available. Additional details are provided in the special terms and conditions, specifications, and online bidding instructions.

Lot 4: Vendor to install cribbing at slide location as directed by the Engineer. Extend wall cribbing 2 feet to 12 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Use wall cribbing: recycled ( used) steel " w" beam guardrail shall be supplied by the KY Dept. of Transportation. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attach to the drilled railroad rails will be furnished by the vendor. The Vendor is responsible for picking up the ( used) steel " W" beam guardrail at the local county Maintenance garage. Any unused ( used) steel " W" beam guardrail shall be returned to the maintenance garage by the vendor. This line item shall be used for all work paid using STATE funds.
Lot 7: Vendor to furnish and install cribbing at slide location as directed by the Engineer. Vendor furnished cribbing must be galvanized guardrail, reinforced concrete panels, or equivalent material as approved by the engineer. The cribbing material must be corrosion resistant and be capable of holding backfill material across a span of 3 to 4 feet. Extend wall cribbing 2 feet to 12 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attaching to the drilled railroad rails will be furnished by the vendor. This line item shall be used for all work paid using STATE funds.

Lot 4: Vendor to install cribbing at slide location as directed by the Engineer. Extend wall cribbing 2 feet to 12 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Use wall cribbing: recycled ( used) steel " w" beam guardrail shall be supplied by the KY Dept. of Transportation. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attach to the drilled railroad rails will be furnished by the vendor. The Vendor is responsible for picking up the ( used) steel " W" beam guardrail at the local county Maintenance garage. Any unused ( used) steel " W" beam guardrail shall be returned to the maintenance garage by the vendor. This line item shall be used for all work paid using STATE funds.
Lot 7: Vendor to furnish and install cribbing at slide location as directed by the Engineer. Vendor furnished cribbing must be galvanized guardrail, reinforced concrete panels, or equivalent material as approved by the engineer. The cribbing material must be corrosion resistant and be capable of holding backfill material across a span of 3 to 4 feet. Extend wall cribbing 2 feet to 12 feet as directed by Engineer below the existing ground line. If bedded rock is encountered, install the cribbing to the bedded rock only. The engineer will direct changes if necessary to the procedure. Vendor to furnish all labor and equipment to deliver and install wall cribbing on the recycled ( used) railroad rail piling. Wall cribbing shall be lapped, bolted, and attached solid to the drilled railroad rails. Bolts, tie wire, welding, etc. needed to make the cribbing panels and attaching to the drilled railroad rails will be furnished by the vendor. This line item shall be used for all work paid using STATE funds.

The Department of Veterans Affairs is conducting market research to identify potential vendors for durable medical equipment services at 12 facilities. The applicable NAICS code is **** parties must submit a response by 10:00 AM Central Time on March 3, 2025, via email to ***@***. *. * response should include organizational information and tailored capability statements. No telephone inquiries will be accepted. The procurement method may be set-aside for small businesses, sole-sourced, or procured through full and open competition.